- 您现在的位置：买卖IC网 > Datasheet目录316 > BU9897GUL-WE2 (Rohm Semiconductor)IC EEPROM SERIAL VCSP50L2 Datasheet资料下载
参数资料
| 型号： | BU9897GUL-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 12/25页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM SERIAL VCSP50L2 |
| 标准包装： | 3,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 128K (16K x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 12-UFBGA，CSPBGA |
| 供应商设备封装： | VCSP50L2 |
| 包装： | 带卷 (TR) |
BU9897GUL-W (128Kbit)
Datasheet
I C BUS data communication
I C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long,
● I 2 C BUS communication
2
2
and acknowledge is always required after each byte.
I 2 C BUS carries out data transmission with plural devices connected by 2 communication lines of serial data (SDA) and
serial clock (SCL).
Among devices, there are “master” that generates clock and control communication start and end, and “slave” that is
controlled by addresses peculiar to devices.
EEPROM becomes “slave”. And the device that outputs data to bus during data communication is called “transmitter”,
and the device that receives data is called “receiver”.
SDA
SCL
1-7
8
9
1-7
8
9
1-7
8
9
S
P
START ADDRESS R/W
ACK
DATA
ACK
DATA
ACK STOP
condition
condition
Figure 30. Data transfer timing
○ Start condition (start bit recognition)
? Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL is
'HIGH' is necessary.
? This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this condition is
satisfied, any command is executed.
○ Stop condition (stop bit recognition)
? Each command can be ended by SDA rising from 'LOW' to 'HIGH' when stop condition (stop bit), namely, SCL is 'HIGH'
○ Acknowledge (ACK) signal
? This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In
master and slave, the device (μ-COM at slave address input of write command, read command, and this IC at data
output of read command) at the transmitter (sending) side releases the bus after output of 8bit data.
? The device (this IC at slave address input of write command, read command, and μ-COM at data output of read
command) at the receiver (receiving) side sets SDA 'LOW' during 9 clock cycles, and outputs acknowledge signal (ACK
signal) showing that it has received the 8bit data.
? This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'.
? Each write action outputs acknowledge signal) (ACK signal) 'LOW', at receiving 8bit data (word address and write data).
? Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'. When
acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (μ-COM) side, this IC
continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and
recognizes stop condition (stop bit), and ends read action. And this IC gets in standby status.
○ Device addressing
? Output slave address after start condition from master.
? The significant 4 bits of slave address are used for recognizing a device type.
The device code of this IC is fixed to '1010'.
? The most insignificant bit ( R / W --- READ / WRITE ) of slave address is used for designating write or read action,
and is as shown below.
Setting R / W to 0 --- write (setting 0 to word address setting of random read)
Setting R / W to 1 --- read
Type
Slave address
BU9897GUL-W
1
0
1
0
0
0
0
R / W
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
12/22
TSZ02201-0R2R0G100500-1-2
4.SEP.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BU99901GUZ-WE2 | IC EEPROM 32KBIT 2WIRE VCSP |
| BUK218-50DY,118 | TOPFET DUAL SWITCH D2PAK |
| BVL121200003N | BATTERY CHG UNIV 12VDC @ 1.2A |
| BVW241250003A | BATTERY CHG UNIV 24VDC @ 1.25A |
| C-14245 | RACKMOUNT INTERNAL CHASSIS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU99022NUX-3TR | 功能描述:IC EEPROM I2C BUS 2KB 8VSON 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K （256 x 8 x 2） 速度:400kHz 接口:I2C，2 线串口 电压 - 电源:1.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C（TA） 封装/外壳:8-UFDFN 裸露焊盘 供应商器件封装:VSON008X2030 标准包装:1 |
| BU9910KV | 制造商:ROHM 制造商全称:Rohm 功能描述:Status display LCD driver for PCs with I2C Bus interface |
| BU9928FV | 制造商:未知厂家 制造商全称:未知厂家 功能描述:マルチメディアLSI |
| BU9929FV | 功能描述:IC I/O EXPANDER I2C 16B 28SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - I/O 扩展器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 接口:I²C，JTAG 输入/输出数:9 中断输出:无 频率 - 时钟:400kHz 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 包括:EEPROM |
| BU9929FV-E2 | 功能描述:IC I/O EXPANDER I2C 16B 28SSOP RoHS:是 类别:集成电路 (IC) >> 接口 - I/O 扩展器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:74 系列:- 接口:I²C，JTAG 输入/输出数:9 中断输出:无 频率 - 时钟:400kHz 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:管件 包括:EEPROM |
发布紧急采购，3分钟左右您将得到回复。