参数资料
型号: C8051F018R
厂商: Silicon Laboratories Inc
文件页数: 4/154页
文件大小: 0K
描述: IC 8051 MCU 16K FLASH 64TQFP
标准包装: 1
系列: C8051F018
核心处理器: 8051
芯体尺寸: 8-位
速度: 25MHz
连通性: SMBus(2 线/I²C),SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,温度传感器,WDT
输入/输出数: 32
程序存储器容量: 16KB(16K x 8)
程序存储器类型: 闪存
RAM 容量: 1.25K x 8
电压 - 电源 (Vcc/Vdd): 2.8 V ~ 3.6 V
数据转换器: A/D 8x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 64-TQFP
包装: 剪切带 (CT)
其它名称: 336-1048-1
C8051F018
C8051F019
Figure 14.4. SMB0CN: SMBus Control Register
R
R/W
Reset Value
BUSY
ENSMB
STA
STO
SI
AA
FTE
TOE
00000000
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
SFR Address:
(bit addressable)
0xC0
Bit7:
BUSY: Busy Status Flag.
0: SMBus is free
1: SMBus is busy
Bit6:
ENSMB: SMBus Enable.
This bit enables/disables the SMBus serial interface.
0: SMBus disabled.
1: SMBus enabled.
Bit5:
STA: SMBus Start Flag.
0: No START condition is transmitted.
1: When operating as a master, a START condition is transmitted if the bus is free. (If the
bus is not free, the START is transmitted after a STOP is received.) If STA is set after one
or more bytes have been transmitted or received and before a STOP is received, a repeated
START condition is transmitted. STO should be explicitly cleared before setting STA to
logic 1.
Bit4:
STO: SMBus Stop Flag.
0: No STOP condition is transmitted.
1: Setting STO to logic 1 causes a STOP condition to be transmitted. When a STOP
condition is received, hardware clears STO to logic 0. If both STA and STO are set, a
STOP condition is transmitted followed by a START condition. In slave mode, setting the
STO flag causes SMBus to behave as if a STOP condition was received.
Bit3:
SI: SMBus Serial Interrupt Flag.
This bit is set by hardware when one of 27 possible SMBus states is entered. (Status code
0xF8 does not cause SI to be set.) When the SI interrupt is enabled, setting this bit causes
the CPU to vector to the SMBus interrupt service routine. This bit is not automatically
cleared by hardware and must be cleared by software.
Bit2:
AA: SMBus Assert Acknowledge Flag.
This bit defines the type of acknowledge returned during the acknowledge cycle on the
SCL line.
0: A “not acknowledge” (high level on SDA) is returned during the acknowledge cycle.
1: An “acknowledge” (low level on SDA) is returned during the acknowledge cycle.
Bit1:
FTE: SMBus Free Timer Enable Bit
0: No timeout when SCL is high
1: Timeout when SCL high time exceeds limit specified by the SMB0CR value.
Bit0:
TOE: SMBus Timeout Enable Bit
0: No timeout when SCL is low.
1: Timeout when SCL low time exceeds limit specified by Timer 3, if enabled.
101
Rev. 1.2
相关PDF资料
PDF描述
C8051F206R IC 8051 MCU 8K FLASH 48TQFP
1996771-1 CONN PIN CONTACT GOLD
C8051F023R IC 8051 MCU 64K FLASH 64TQFP
533082-1 CONN PIN GUIDE .375 UNPLATED
2-592404-1 CONN PIN SIZE 20 GOLD CRIMP
相关代理商/技术参数
参数描述
C8051F019 功能描述:8位微控制器 -MCU 16KB 10ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F019-GQ 功能描述:8位微控制器 -MCU 16KB 10ADC 48P MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F019-GQR 功能描述:8位微控制器 -MCU 16KB 10ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F019R 功能描述:8位微控制器 -MCU C+-10Bit/48Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F020 功能描述:8位微控制器 -MCU 16KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT