- 您现在的位置：买卖IC网 > Datasheet目录317 > C8051F912DK (Silicon Laboratories Inc)KIT DEV FOR C8051F91X/C8051F90X Datasheet资料下载
参数资料
| 型号： | C8051F912DK |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 19/25页 |
| 文件大小： | 0K |
| 描述： | KIT DEV FOR C8051F91X/C8051F90X |
| 产品培训模块： | C8051F9xx Lower Power MCUs |
| 视频文件： | Designing for Low Power Operation |
| 特色产品： | C8051F91x/0x MCU Series Development Kit |
| 标准包装： | 1 |
| 类型： | MCU |
| 适用于相关产品： | C8051F91x/0x |
| 所含物品： | 板，电池，线缆，CD，电源适配器，USB 调试适配器 |
| 产品目录页面： | 626 (CN2011-ZH PDF) |
| 其它名称： | 336-1854 |
C8051F91x/90x
6. Frequently Asked Questions
1. Should power be turned off when switching between one-cell and two-cell mode?
Yes, power must be turned off by placing SW5 in the OFF position when switching between one-cell and
two-cell mode. Switching between modes while power is on may result in increased power consumption
and possible damage to low voltage transistors.
2. I have placed the MCU in Sleep Mode. Why is the supply current greater than 1 μA?
This can be caused by a number of factors. Check the following:
a. Verify that the USB Debug Adapter is not connected to the device. When connected, it can draw
approximately 2–5 μA from the VDD/DC+ supply net.
b. Verify that the P1.5 and P1.6 LEDs are turned off in software (P1.5 and P1.6 set to logic HIGH).
Alternatively, the P1.5 and P1.6 LEDs can be disabled by removing the corresponding shorting blocks
from J8.
c. Verify that the VDD/DC+ Power LED is disabled (remove shorting block from J5).
d. Verify that the shorting block on J15 does not connect the potentiometer negative terminal to GND,
since this would result in continuous current of ~ 300 μA. The shorting block may be removed, or
configured to enable the potentiometer when P1.4 is set to logic LOW. When the potentiometer enable
is under software control, be sure to set P1.4 to logic HIGH prior to placing the device in Sleep Mode.
e. Verify that J7, J13, and J14 do not have shorting blocks installed.
3. I have been measuring the sleep mode current using the “μA” setting on my multimeter. Why am I
no longer able to connect to the IDE?
When most multimeters are placed in “μA” mode, a large resistance is placed in series with the power
supply. This “current limiting” resistor prevents the MCU from starting up. To measure current during
startup, make sure that the multimeter is configured to its “mA” setting.
Alternatively, a shorting block can be placed on J17 to ensure that the multimeter does not limit current
during startup.
4. Where can I find a schematic of the C8051F912 Target Board?
A target board schematic can be found in the C8051F912-DK User ’s Guide which is available on the
Development Tools CD and is installed in the following folder (by default):
C:\SiLabs\MCU\Documentation\UsersGuides
5. Which power LED should I use to determine if the MCU is powered?
The VDD/DC+ LED (DS5) should be used to determine if the MCU is powered. If you have applied power
to the board, but the VDD/DC+ LED is not turning on, check the following:
a. Verify that the correct power source (J10, J11) is selected.
b. Verify that J17 has a shorting block.
c. Verify that SW5 is in the ON position.
d. Verify that J5 has a shorting block installed.
Rev. 0.2
19
相关PDF资料 |
PDF描述 |
|---|---|
| C8051F930-TB | BOARD TARGET/PROTO W/C8051F930 |
| C8051T610DB24 | DAUGHTER BOARD T610 24QFN SOCKET |
| C8051T630DB20 | BOARD SOCKET DAUGHTER 20-QFN |
| CAN-100 | BOARD EVAL RS232 100QFP |
| CANADAPT28 | KIT ADAPTER CANDEMOBOARD 28PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| C8051F912-GDI | 功能描述:8位微控制器 -MCU 16kB Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F912-GM | 功能描述:8位微控制器 -MCU 16KB 12ADC 24QFN RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F912-GMR | 功能描述:8位微控制器 -MCU 16KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F912-GU | 功能描述:8位微控制器 -MCU 16KB 12ADC 24QSOP RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F912-GUR | 功能描述:8位微控制器 -MCU 16KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。