- 您现在的位置：买卖IC网 > PDF目录20022 > CAT28F001G-12TT (ON Semiconductor)IC FLASH 1MBIT 120NS 32PLCC PDF资料下载
参数资料
| 型号： | CAT28F001G-12TT |
| 厂商： | ON Semiconductor |
| 文件页数： | 12/18页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 1MBIT 120NS 32PLCC |
| 产品变化通告： | Product Obsolescence 05/Oct/2010 |
| 标准包装： | 500 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | FLASH |
| 存储容量： | 1M (128K x 8) |
| 速度： | 120ns |
| 接口： | 并联 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 32-LCC（J 形引线） |
| 供应商设备封装： | 32-PLCC（11.43x13.97） |
| 包装： | 带卷 (TR) |
CAT28F001
Figure 5 Block Erase Flowchart
START
Bus
Operation
Command
Comments
WRITE 20H,
BLOCK ADDRESS
WRITE D0H
BLOCK ADDRESS
READ STATUS
Write
Write
Read
Erase
Setup
Erase
Data = 20H
Address = Within Block to be erased
Data - D0H
Address = Within Block to be erased
Status Register Data.
REGISTER
NO
ERASE SUSPEND
LOOP
Toggle OE or CE to update
Status Register
SR.7 = 1?
NO
SUSPEND
ERASE?
YES
Standby
Check SR.7
1 = Ready, 0 = Busy
YES
FULL STATUS
CHECK IF DESIRED
BLOCK ERASE
COMPLETED
FULL STATUS CHECK PROCEDURE
STATUS REGISTER DATA
READ (SEE ABOVE)
Repeat for subsequent blocks.
Full Status check can be done after each block or after a sequence
of blocks.
Write FFH after the last block erase operation to reset the device to
Read Array Mode.
Bus
Operation
Command
Comments
SR.3 = 0?
NO
V PP RANGE
ERROR
Standby
Check SR.3
1 = V PP Low Detect
YES
SR.4,5 = 1?
YES COMMAND SEQUENCE
ERROR
Standby
Check SR.4
Both 1 = Command Sequence Error
NO
SR.5 = 0?
NO
BLOCK ERASE
ERROR
Standby
Check SR.5
1 = Block Erase Error
SR.3 MUST be cleared, if set during a erase attempt, before further
BLOCK ERASE
SUCCESSFUL
attempts are allowed by the Write State Machine.
SR.3 is only cleared by the Clear Status Register Command, in
cases where multiple blocks are erased before full status is
checked.
If error is detected, clear the Status Register before attempting retry
or other error recovery.
Doc. No. MD-1078, Rev. K
12
? 2008 SCILLC. All rights reserved.
Characteristics subject to change without notice
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5955BUEE+ | IC DUAL HOT-SWAP CTRLR 16-QSOP |
| CAT28F001G-12T | IC FLASH 1MBIT 120NS 32PLCC |
| VI-JNP-CX-S | CONVERTER MOD DC/DC 13.8V 75W |
| GRM155R61A105KE15D | CAP CER 1UF 10V 10% X5R 0402 |
| 208008-1 | CONN D-SUB PLUG STR 25POS PCB AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CAT28F001G-12-T-T | 制造商:ON Semiconductor 功能描述:Flash Parallel 5V 1Mbit 128K x 8bit 120ns 32-Pin PLCC T/R |
| CAT28F001G-90B | 功能描述:闪存 (128x8) 1M 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| CAT28F001G-90BT | 功能描述:闪存 1 Megabit Boot Block 闪存 Memory RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| CAT28F001G-90T | 功能描述:闪存 (128x8) 1M 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| CAT28F001G-90TT | 功能描述:闪存 1 Megabit Boot Block 闪存 Memory RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。