- 您现在的位置：买卖IC网 > PDF目录16993 > CDB5526 (Cirrus Logic Inc)EVAL BOARD FOR CS5526 PDF资料下载
参数资料
| 型号： | CDB5526 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 6/30页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR CS5526 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 20 |
| 采样率（每秒）： | 606 |
| 数据接口： | 串行 |
| 输入范围： | ±2.5 V |
| 在以下条件下的电源（标准）： | 9.4mW @ 15SPS，5 V |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | CS5526 |
| 已供物品： | 板，CD |
| 相关产品： | CS5526-BSZR-ND - IC ADC 20BIT W/4BIT LATCH 20SSOP 598-1108-5-ND - IC ADC 20BIT W/4BIT LATCH 20SSOP |
| 其它名称： | 598-1014 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
CS5525 CS5526
14
DS202F5
Analog Input
Figure 7 illustrates a block diagram of the analog in-
put signal path inside the CS5525/26. The front end
consists of a chopper-stabilized instrumentation am-
plifier with 20X gain and a programmable gain sec-
tion. The instrumentation amplifier is powered from
VA+ and from the NBV (Negative Bias Voltage) pin
allowing the CS5525/26 to be operated in either of
two analog input configurations. The NBV pin can
be biased to a negative voltage between -1.8 V and
-2.5 V, or tied to AGND. The choice of the operating
mode for the NBV voltage depends upon the input
signal and its common mode voltage.
For the 25 mV, 55 mV, and 100 mV input ranges, the
input signals to AIN+ and AIN- are amplified by the
20X instrumentation amplifier. For ground refer-
enced signals with magnitudes less then 100 mV, the
NBV pin should be biased with -1.8 V to -2.5 V. If
NBV is tied between -1.8 V and -2.5 V, the (Com-
mon Mode + Signal) input on AIN+ and AIN- must
stay between -0.150 V and 0.950 V to ensure prop-
er operation. Alternatively, NBV can be tied to
AGND where the input (Common Mode + Signal)
on AIN+ and AIN- must stay between 1.85 V and
2.65 V to ensure that the amplifier operates prop-
erly.
For the 1 V, 2.5 V, and 5 V input ranges, the instru-
mentation amplifier is bypassed and the input sig-
nals are directly connected to the Programmable
Gain block. With NBV tied between -1.8 V and
-2.5 V, the (Common Mode + Signal) input on
AIN+ and AIN- must stay between NBV and VA+.
Alternatively, NBV can be tied to AGND where
the input (Common Mode + Signal) on AIN+ and
AIN- pins can span the entire range between
AGND and VA+.
The CS5525/26 can accommodate full scale ranges
other than 25 mV, 55 mV, 100 mV, 1 V, 2.5 V and
5 V by performing a system calibration within the
limits specified. See the Calibration section for
more details. Another way to change the full scale
range is to increase or to decrease the voltage refer-
ence to other than 2.5 V. See the Voltage Refer-
ence section for more details.
Three factors set the operating limits for the input
span. They include: instrumentation amplifier satu-
ration, modulator 1’s density, and a lower reference
voltage. When the 25 mV, 55 mV or 100 mV range
is selected, the input signal (including the common
mode voltage and the amplifier offset voltage)
must not cause the 20X amplifier to saturate in ei-
ther its input stage or output stage. To prevent sat-
uration the absolute voltages on AIN+ and AIN-
must stay within the limits specified (refer to the
‘Analog Input’ table on page 3). Additionally, the
differential output voltage of the amplifier must not
exceed 2.8 V. The equation
ABS(VIN + VOS) x 20 = 2.8 V
defines the differential output limit, where
VIN = (AIN+) - (AIN-)
is the differential input voltage and VOS is the ab-
solute maximum offset voltage for the instrumenta-
tion amplifier (VOS will not exceed 40 mV). If the
VR EF +
D ifferen tial 4th
ord er d elta-
s igm a m o d ula tor
D ig ita l F ilter
AIN +
AIN -
Pro g ra m m a b le
Ga in
VR EF -
NBV
X2 0
Figure 7. Block Diagram of Analog Signal Path
相关PDF资料 |
PDF描述 |
|---|---|
| 1025R-40K | COIL 6.8UH MOLDED UNSHIELDED |
| 222A111-4/86-0 | BOOT MOLDED |
| VI-J0Y-EX | CONVERTER MOD DC/DC 3.3V 49.5W |
| VE-J7V-EY | CONVERTER MOD DC/DC 5.8V 50W |
| 0150150623 | CABLE FLAT FLEX 23POS .3MM 6" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB5528 | 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Evaluation Board and Software |
| CDB5529 | 功能描述:EVAL BOARD FOR CS5529 RoHS:否 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| CDB5530U | 功能描述:数据转换 IC 开发工具 Eval Bd 24-Bit 1-Ch Low-Noise ADC RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| CDB5532U | 功能描述:数据转换 IC 开发工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| CDB5534U | 功能描述:数据转换 IC 开发工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
发布紧急采购，3分钟左右您将得到回复。