- 您现在的位置：买卖IC网 > Datasheet目录969 > CDB5581 (Cirrus Logic Inc)BOARD EVAL FOR CS5581 ADC Datasheet资料下载
参数资料
| 型号： | CDB5581 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 6/26页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR CS5581 ADC |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 200k |
| 数据接口： | 串行 |
| 输入范围： | ±2.048 V |
| 在以下条件下的电源（标准）： | 85mW @ 200kSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | CS5581 |
| 已供物品： | 板 |
| 相关产品： | 598-1272-5-ND - IC ADC 16BIT 1CH 200KSPS 24SSOP |
| 其它名称： | 598-1559 |
CDB5581
3. HARDWARE DESCRIPTION
3.1
Absolute Maximum Ratings
Observe the following limits to ensure the CDB5581 component ratings are not exceeded.
? CS5581
– The absolute maximum supply voltage that can be applied to the +3.3V power supply
connection is +3.6V.
– The absolute maximum power supply voltage that can be applied between pins VL and V1-
is 6.1 V.
? CS3004
– The absolute maximum power supply voltage that can be applied between the +2.5V and
-2.5V power supply connections is +5.5V.
3.2
Power Supply
Power supply connections and requirements are specified in Table 1. below.
Table 1. Power Supply Connections
Power Supply
Requirement
+2.5 V DC, ±5%, <50 mA
-2.5 V DC, ±5%, <50 mA
+3.3 V DC, ±5%, <50 mA
Power Supply
Connection
E5
E9
E16
Associated
Ground Return
E3
E7
E13
Associated
Test Points
TP2, TP1 (GND)
TP4, TP3 (GND)
TP6, TP5 (GND)
Important: It is recommended that all power supplies be isolated from utility ground to prevent the intro-
duction of a ground loop. One ground connection may already exist through the serial port connection to
utility ground. Using the Cirrus Logic CapturePlus II system simplifies making connections to the
CDB5581 by providing electrical isolation between the two.
Using twisted/shielded wire will reduce electrical noise induced onto the power supply cables.
Power supplies are to be adequately regulated and sufficiently low noise to meet the application require-
ments.
3.3
3.3.1
Analog Section
Analog Input Buffers
The analog input signal connections to the input buffers are made at the IN_A and IN_B connectors, as
Table 2. Analog Input Connections
Analog Input
Input Signal
Channel
IN_A
IN_B
Connection
J10
J11
Voltage Range
-2.048 V to +2.048 V
-2.048 V to +2.048 V
Impedance
50 Ohms
50 Ohms
There are two analog input channels on the evaluation board. Each analog input channel consists of a
low-noise amplifier configured as a unity gain non-inverting buffer. The buffers utilize a Cirrus Logic
CS3004 precision, low-noise, low-voltage, dual opamp.. These op-amps enable both the inputs and out-
puts of the analog input buffer to operate virtually rail to rail. The channel input impedance is 50 Ohms.
6
DS796DB3
相关PDF资料 |
PDF描述 |
|---|---|
| CDK5571 | CDB5571 W/CAPTURE PLUS 2 SYSTEM |
| CDK5581 | KIT BOARD FOR CDB5581 ADC |
| CF1176-000 | SHIELD TERMINATOR |
| SMS4SE4K9 | 集管和线壳 4P QIKMATE PIN STRT PC BOARDMOUNT |
| CF6147-000 | CABLE TERMINATION |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB56-A | 制造商:Panduit Corp 功能描述: |
| CDB572 | 制造商: 功能描述: 制造商:Rockwell Automation / Allen-Bradley 功能描述: |
| CDB5S-A-L | 制造商:Panduit Corp 功能描述: |
| CDB6/2 | 功能描述:接线端子板接口模块 Feed-thru Term Dble level RoHS:否 制造商:Phoenix Contact 类型:Isolating Amplifier 节距: 位置/触点数量:2 线规量程: 电流额定值: 电压额定值:24 V 安装风格:DIN Rail 安装角: 端接类型:Screw 触点电镀: |
| CDB6/3 | 功能描述:接线端子板接口模块 lightning Arrestor 3pole RoHS:否 制造商:Phoenix Contact 类型:Isolating Amplifier 节距: 位置/触点数量:2 线规量程: 电流额定值: 电压额定值:24 V 安装风格:DIN Rail 安装角: 端接类型:Screw 触点电镀: |
发布紧急采购，3分钟左右您将得到回复。