- 您现在的位置：买卖IC网 > PDF目录378798 > CDS-1402MC (Electronic Theatre Controls, Inc.) 14-Bit, Very Fast Settling Correlated Double Sampling Circuit PDF资料下载
参数资料
| 型号： | CDS-1402MC |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 14-Bit, Very Fast Settling Correlated Double Sampling Circuit |
| 中文描述： | 14位，非常快速沉降相关双采样电路 |
| 文件页数： | 5/8页 |
| 文件大小： | 203K |
| 代理商： | CDS-1402MC |
CDS -1402
5
Timing Notes
See Figure 2, Typical Timing Diagram. It is advisable that
neither of the CDS-1402's S/H amplifiers be in their sample/
track mode when large, high-speed transients (normally
associated with clock edges) are occurring throughout the
system. This could result in the S/H amplifiers being driven
into saturation, and they may not recover in time to accurately
acquire their next signal.
For example, S/H1 should not be commanded into the sample
mode until all transients associated with the opening of the
shunt switch have begun to decay. Similarly, S/H2 should not
be driven into the sample mode until all transients associated
with the clocking of pixel charge onto the output capacitor
have begun to decay. Therefore, it is generally not a good
practice to use the same clock edge to drive S/H1 into hold
(holding the offset) and S/H2 into sample (to acquire the offset
+ video signal).
S/H's that are in their signal-acquisition modes should be left
there as long as possible (so all signals can settle) and be
driven into their hold modes before any system transients
occur. In Figure 2, S/H1 is driven into the sample mode
shortly after the transient from the shunt switch has begun to
decay. S/H1 is then kept in the sample mode while the offset
signal and the S/H output settle. S/H1 is driven into hold just
prior to the system clock pulse(s) that transfers the next pixel
charge onto the output capacitor.
package so they can be used to control other circuit functions.
Each S/H has two pins for offset adjusting (if required), one for
current and one for voltage.
In normal operation, the output signal of the CCD is applied
simultaneously to the inputs (pins 3 and 4) of both S/H
amplifiers. S/H1 will normally be used to capture and hold
each pixel’s offset signal. Therefore, S/H1 is initially in its
signal-acquisition mode (logic "1" applied to pin 11, S/H1
COMMAND). This is also called the sample or track mode.
Following a brief interval during which the output of the CCD
and the output of S/H1 are allowed to settle, S/H1 is driven into
its hold mode by applying a logic "0" to pin 11. S/H1 is now
holding the pixel's offset value.
In most straightforward configurations, the output of S/H1 is
connected to the summing node of S/H2 by connecting pin 7
(S/H1 ROUT) to pin 8 (S/H2 SUMMING NODE).
When the offset+video signal appears at the output of the CCD,
S/H2 is driven into its signal acquisition mode by applying a
logic "1" to pin 12 (S/H2 COMMAND).
S/H2 employs a current-summing architecture that subtracts
the output of S/H1 (the offset) from the output of the CCD
(offset+video) while acquiring only the difference signal (i.e.,
the valid video). A logic "0" subsequently applied to pin 12
drives S/H2 into its hold mode, and after a brief transient
settling time, the valid video signal appears at pin 22 (V OUT).
Figure 3. CDS-1402 in Front of DATEL's ADC-944 at f
CLK
= 4MHz
S/H1
S/H2
START CONVERT
EOC
OUTPUT
DATA
DATA N-1 VALID
DATA N VALID
30ns typ.
35ns typ.
50ns max.
ANALOG INPUT
FOR CDS
(Pins 3 and 4 are tied together)
(CCD OUTPUT)
100ns
100ns
OFFSET (N+1)
OFFSET +
VIDEO (N+1)
OFFSET (N+2)
OFFSET +
VIDEO (N+2)
150ns
DATA N+1 VALID
10ns min.
相关PDF资料 |
PDF描述 |
|---|---|
| CDS-1402 | 14-Bit, Very Fast Settling Correlated Double Sampling Circuit |
| CDS-1402MM | 14-Bit, Very Fast Settling Correlated Double Sampling Circuit |
| CDS15FD331J03 | Miniature Dipped, Mica Capacitors |
| CDS15CD180J03 | Miniature Dipped, Mica Capacitors |
| CDS15ED200J03 | Miniature Dipped, Mica Capacitors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDS-1402MM | 制造商:Murata Power Solutions 功能描述:Correlated Double Sampler (Cds) 24-Pin CDDIP |
| CDS14N | 功能描述:SOCKET,1/4" DRIVE,7MM,6PT 制造商:apex tool group 系列:* 零件状态:在售 标准包装:1 |
| CDS15 | 功能描述:保险丝 CARTRIDGE D 15A RoHS:否 制造商:Littelfuse 产品:Surface Mount Fuses 电流额定值:0.5 A 电压额定值:600 V 保险丝类型:Fast Acting 保险丝大小/组:Nano 尺寸:12.1 mm L x 4.5 mm W 安装风格: 端接类型:SMD/SMT 系列:485 |
| CDS150 | 功能描述:保险丝 CNDIAN D-TYP 600V TD RoHS:否 制造商:Littelfuse 产品:Surface Mount Fuses 电流额定值:0.5 A 电压额定值:600 V 保险丝类型:Fast Acting 保险丝大小/组:Nano 尺寸:12.1 mm L x 4.5 mm W 安装风格: 端接类型:SMD/SMT 系列:485 |
| CDS-15118B | 功能描述:8 Ohm Magnetic Speaker 700mW 20Hz ~ 20kHz Top Rectangular 86dB 制造商:cui inc. 系列:CDS 零件状态:有效 类型:磁性 频率范围:20Hz ~ 20kHz 阻抗:8 欧姆 声压级:86dB 功率 - 额定值:700mW 功率 - 最大值:1W 端口位置:顶部 形状:矩形 材料 - 锥体:PET 材料 - 磁铁:Nd-Fe-B 端接:焊盘 大小/尺寸:15.00mm 长 x 11.00mm 宽 高度:3.10mm 标准包装:100 |
发布紧急采购，3分钟左右您将得到回复。