- 您现在的位置：买卖IC网 > PDF目录6258 > CPC5902G (IXYS Integrated Circuits Division)ISOLAT 3.75KVRMS 2CH BIDIR 8DIP PDF资料下载
参数资料
| 型号： | CPC5902G |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | ISOLAT 3.75KVRMS 2CH BIDIR 8DIP |
| 标准包装： | 50 |
| 电压 - 隔离： | 3750Vrms |
| 通道数： | 2，双向 |
| 数据速率： | 400kbps |
| 输入类型： | AC，DC |
| 输出类型： | I²C? |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-DIP |
| 包装： | 管件 |
| 其它名称： | CLA380 |
I C bus is chosen based upon the expected V DD
I NTEGRATED C IRCUITS D IVISION
3.2 Calculating Minimum Pull-Up Resistor Values
The minimum value of the pull-up resistor, R PU , on the
2
supply voltage range and the weakest load current
sinking device on the bus. Note: Systems that do not
need maximum bandwidth and busses with lower
capacitive loading can use a higher value for the
pull-up resistor to reduce power consumption.
3.2.1 Side A Pull-Up Resistor: R PUA
The weakest I 2 C compliant device on the Side A bus,
with R PUA to V DDA , must be able to pull the Side A
inputs below 0.4V for outputs rated at 3mA or 0.6V for
outputs rated at 6mA when V DDA is at its maximum.
For example, if the weakest device is only guaranteed
to sink 3mA then the maximum allowed logic low
output voltage will be 0.4V. For designs with
V DDA_max = 3.6V, the minimum voltage across the
pull-up resistor is:
Minimum R PUA Voltage = 3.6 - 0.4 = 3.2V
For the I 2 C minimum current sink requirement of 3mA,
the minimum value of the pull-up resistor is easily
calculated as:
R PUA_min = 3.2V / 3mA = 1066.7 ?
Chose a standard value resistor that will not violate
this minimum value over tolerance and temperature,
such as a 1.1k ? , 1% tolerance, 100ppm/ ? C
temperature coefficient resistor.
If all the non-CPC5902 devices on the Side A bus are
Fast-mode compliant (400pF capacitive loading
capable) with the required 6mA current sink capability,
then the bus can be configured for Fast-mode.
Resistor selection for Fast-mode is similar to the
example given above but because the logic low output
level is greater (0.6V) then the voltage across the
pull-up resistor will be less. Calculation of the
compliant Fast-mode bus minimum pull-up resistor
value is given by:
R PUA_min = (3.6 - 0.6)V / 6mA = 500 ?
The minimum E96 standard value 1% tolerance,
100ppm/ ? C temperature coefficient resistor is 511 ? .
3.2.2 Side B Pull-Up Resistor: R PUB
Calculating the pull-up resistor for Side B is similar to
the process used for Side A but with some additional
considerations.
CPC5902
Before proceeding, it must be pointed out that Side B
of the CPC5902 is Fast-mode compliant with
V DDB ? 4.5V. This means the CPC5902 Side B
outputs are 6mA capable allowing bus operation of
400kb/s with up to 400pF of capacitive loading. For
V DDB supply levels below 4.5V the CPC5902 outputs
are only rated for 3mA but can be operated at
Fast-mode speeds of 400kb/s whenever the bus
capacitive loading C LOAD ? 200pF. Greater capacitive
loading of the Side B bus limits the CPC5902 to data
rates of 100kb/s.
First, it must be determined if the Side B bus will be
configured for 3mA or 6mA operation. This is done by
evaluating the external (non-CPC5602) devices on the
Side B bus and the operational capabilities of the
CPC5902. There are three possibilities:
1) One or more of the external devices is limited to
3mA of output current sink.
2) All of the external devices are rated at 6mA of
output current sink and the Side B minimum supply
voltage V DDB ? 4.5V.
3) All of the external devices are rated at 6mA of
output current sink and the Side B minimum supply
voltage V DDB ? 4.5V.
For conditions 1 and 2 above the bus must be
configured for 3mA. Condition 3 is the only situation
where the bus can be configured for 6mA, a
Fast-mode requirement when capacitive bus loading is
an issue.
Second, it is necessary to configure the Side B bus to
be compatible with the CPC5902’s lower logic low
input threshold:
V ILB = 0.2 ? V DDB - 60mV
As discussed earlier, this lower input threshold
requirement is to ensure the CPC5902 can drive a
logic low output that is recognized by the other I 2 C
devices on the bus, but will not accept it’s own logic
low output. This prevents latching of the CPC5902.
Additionally, this implies there can be no more than
one limited drive (Side B) CPC5902 interface on the
Side B bus, and that all other devices on the Side B
bus must have V IL = 0.3 ? V DDB logic low input
thresholds. Because the CPC5902 Side A inputs are
compatible with this requirement, any number of
10
www.ixysic.com
R03
相关PDF资料 |
PDF描述 |
|---|---|
| CST3104 | BOX STEEL 36X6X4" GREY |
| PJ12106W | BOX FIBER 13.8X11.9X6.47" GREY |
| 1414PHRO6LP | BOX STEEL 14.0X16.0X6.0" GREY |
| PJ16148P30 | BOX FIBER 17.9X16.0X8.47" GREY |
| 094036150 | BOX ABS 15.75X14.17X5.91" GRAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC5902G_5903G-EVAL | 功能描述:CPC5902, CPC5903 - Interface, Buffer/Repeater Evaluation Board 制造商:ixys integrated circuits division 系列:- 零件状态:有效 主要用途:接口，缓冲器/中继器 嵌入式:- 使用的 IC/零件:CPC5902，CPC5903 主要属性:隔离 辅助属性:- 所含物品:板 标准包装:1 |
| CPC5902GS | 功能描述:ISOLAT 3.75KVRMS 2CH BIDIR 8SMD RoHS:是 类别:隔离器 >> 光隔离器 - 逻辑输出 系列:- 标准包装:1,000 系列:- 电压 - 隔离:3750Vrms 通道数:1，单向 电流 - 输出 / 通道:50mA 数据速率:15MBd 传输延迟高 - 低 @ 如果:50ns @ 7.5mA 电流 - DC 正向(If):20mA 输入类型:DC 输出类型:开路集电极 安装类型:表面贴装 封装/外壳:8-SMD，鸥翼型 供应商设备封装:8-DIP 鸥翼型 包装:带卷 (TR) |
| CPC5902GSTR | 功能描述:ISOL 3.75KVRMS 2CH BIDIR 8-SMD RoHS:是 类别:隔离器 >> 光隔离器 - 逻辑输出 系列:- 标准包装:50 系列:- 电压 - 隔离:3750Vrms 通道数:1，单向 电流 - 输出 / 通道:10mA 数据速率:25MBd 传输延迟高 - 低 @ 如果:20ns 电流 - DC 正向(If):- 输入类型:逻辑 输出类型:推挽式/图腾柱 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:516-1112-5 |
| CPC5903G | 功能描述:ISOL 3.75KVRMS 1CH BIDIR 8-DIP RoHS:是 类别:隔离器 >> 光隔离器 - 逻辑输出 系列:- 标准包装:50 系列:- 电压 - 隔离:3750Vrms 通道数:1，单向 电流 - 输出 / 通道:10mA 数据速率:25MBd 传输延迟高 - 低 @ 如果:20ns 电流 - DC 正向(If):- 输入类型:逻辑 输出类型:推挽式/图腾柱 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:516-1112-5 |
| CPC5903GS | 功能描述:ISOL 3.75KVRMS 1CH BIDIR 8-SMD RoHS:是 类别:隔离器 >> 光隔离器 - 逻辑输出 系列:- 标准包装:50 系列:- 电压 - 隔离:3750Vrms 通道数:1，单向 电流 - 输出 / 通道:10mA 数据速率:25MBd 传输延迟高 - 低 @ 如果:20ns 电流 - DC 正向(If):- 输入类型:逻辑 输出类型:推挽式/图腾柱 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:516-1112-5 |
发布紧急采购，3分钟左右您将得到回复。