- 您现在的位置：买卖IC网 > PDF目录1786 > CPC5903GSTR (IXYS Integrated Circuits Division)ISOL 3.75KVRMS 1CH BIDIR 8-SMD PDF资料下载
参数资料
| 型号： | CPC5903GSTR |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | ISOL 3.75KVRMS 1CH BIDIR 8-SMD |
| 标准包装： | 1,000 |
| 电压 - 隔离： | 3750Vrms |
| 通道数： | 1，双向 |
| 数据速率： | 400kbps |
| 输入类型： | DC |
| 输出类型： | I²C? |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SMD，鸥翼型 |
| 供应商设备封装： | 8-SMD |
| 包装： | 带卷 (TR) |
I NTEGRATED C IRCUITS D IVISION
4.2.2 IOB Pull-Up Resistor: R PUB
For the bidirectional buffer, it is necessary to configure
the IOB bus to be compatible with the CPC5903’s
lower logic low input threshold:
V ILB = 0.2 ? V DDB - 60mV
As discussed earlier, this lower input threshold
requirement is to ensure the CPC5903 can drive a
logic low output that is recognized by the other I 2 C
devices on the bus, but will not accept it’s own logic
low output. This prevents latching of the CPC5903.
Additionally, this implies there can be no more than
one limited drive (Side B) CPC5903 interface on the
IOB bus, and that all other devices on the bus must
have V IL = 0.3 ? V DDB logic low input thresholds.
Because the CPC5903 Side A inputs are compatible
with this requirement, any number of CPC5903 Side A
devices may be connected to the Side B bus.
For all modes, the minimum required voltage drop
across the IOB pull-up resistor at V DDB_max by the
external non-CPC5903 I 2 C bus drivers is:
Minimum R PUB Voltage = V DDB_max - (0.2 ? V DDB_max - 60mV)
= 0. 8 ? V DDB_max + 60mV
which gives the calculation for the minimum value of
the pull-up resistor as:
R PUB_min = (0. 8 ? V DDB_max + 60mV) / I OL
where I OL is the guaranteed logic low drive current of
the non-CPC5903 bus drivers.
For Standard-mode designs, with output drivers rated
at 3mA and a maximum supply voltage of 3.6V, the
minimum value of the pull-up resistor is:
R PUB_min = (0. 8 ? 3.6 + 60mV) / 3mA = 9 8 0 ?
The minimal standard value 1% resistor with a
100ppm/ ? C temperature coefficient that will not go
below the calculated minimum due to tolerance and
temperature is 1k ? .
In Fast-mode designs with 6mA capable output drivers
and a supply voltage maximum of 5.5V, the minimum
Fast-mode pull-up resistor value is calculated to be:
R PUB_min = (0. 8 ? 5.5 + 60mV) / 6mA = 743.3 ?
For a Fast-mode design with high capacitive bus
loading, a 768 ? , 1%, 100ppm/ ? C resistor would
suffice. When the bus does not have a heavy
capacitive load, a larger value pull-up resistor can be
used thereby reducing overall power consumption.
CPC5903
12
www.ixysic.com
R02
相关PDF资料 |
PDF描述 |
|---|---|
| CS1601-FSZ | IC PFC CONTROLLER BALLAST 8SOIC |
| CS2001YDWFR20 | IC REG BST FLYBK ADJ 1.2A 20SOIC |
| CS2841BEDR14G | IC REG CTRLR BST FLYBK CM 14SOIC |
| CS5101EN14G | IC REG BUCK 5V 1.5A 14DIP |
| CS51033GDR8G | IC REG CTRLR BUCK PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CPC60AFC | 制造商:SENSORTECHNICS 制造商全称:Sensortechnics GmbH 功能描述:Precision compensated pressure sensors / mV-output |
| CPC60AH | 功能描述:板上安装压力/力传感器 ASG/SENSYM RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
| CPC60DFC | 功能描述:工业压力 / 力传感器 ASG/SENSYM RoHS:否 制造商:Honeywell 工作压力:0 bar to 25 bar 压力类型:Sealed Gauge 准确性:0.25 % 输出类型: 安装风格:Screw 工作电源电压:8 V to 30 V 输出电压:8 V to 30 V 封装: |
| CPC60GFC | 制造商:Honeywell / Clarostat 功能描述:ASG/SENSYM 制造商:Honeywell Sensing and Control 功能描述:ASG/SENSYM 制造商:Honeywell Sensing and Control 功能描述:CPC60GFC ASG/SENSYM |
| CPC60GFH | 功能描述:板上安装压力/力传感器 ASG/SENSYM 130 - CPC,CPCL RoHS:否 制造商:Honeywell 工作压力:0 bar to 4 bar 压力类型:Gage 准确性:+ / - 0.25 % 输出类型:Digital 安装风格:Through Hole 工作电源电压:5 V 封装 / 箱体:SIP 端口类型:Dual Radial Barbed, Same sides |
发布紧急采购，3分钟左右您将得到回复。