参数资料
| 型号： | CS4360-DZZ |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 20/37页 |
| 文件大小： | 0K |
| 描述： | IC DAC STER 6CH 102DB 28TSSOP |
| 标准包装： | 50 |
| 位数： | 24 |
| 数据接口： | 串行 |
| 转换器数目： | 6 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 265mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 输出数目和类型： | 6 电压，单极 |
| 采样率（每秒）： | 192k |
| 其它名称： | 598-1056-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
CS4360
DS517F2
27
4.9.2b
IC Read
To read from the device, follow the procedure below while adhering to the control port Switching Specifi-
cations. During this operation it is first necessary to write to the device, specifying the appropriate register
through the MAP.
1) After writing to the MAP (see section 4.9.1), initiate a repeated START condition to the IC bus fol-
lowed by the address byte. The upper 6 bits must be 001000. The seventh bit must match the setting
of the AD0 pin, and the eighth must be 1. The eighth bit of the address byte is the R/W bit.
2) Signal the end of the address byte by not issuing an acknowledge. The device will then transmit the
contents of the register pointed to by the MAP. The MAP will contain the address of the last register
written to the MAP.
3) If the INCR bit is set to 1, the device will continue to transmit the contents of successive registers. Con-
tinue providing a clock but do not issue an ACK on the bytes clocked out of the device. After all the
desired registers are read, initiate a STOP condition to the bus.
4) If the INCR bit is set to 0 and further IC reads from other registers are desired, it is necessary to repeat
the procedure detailed from step 1. If no further reads from other registers are desired, initiate a STOP
condition to the bus.
4.9.3
SPI Mode
In SPI mode, data is clocked into the serial control data line, CDIN, by the serial control port clock, CCLK
(see Figure 21 for the clock to data relationship). There is no AD0 pin. Pin CS is the chip select signal and
is used to control SPI writes to the control port. When the device detects a high-to-low transition on the
AD0/CS pin after power-up, SPI mode will be selected. All signals are inputs and data is clocked in on the
rising edge of CCLK.
SD A
SC L
001000
A D 0
W
Sta rt
AC K
MA P
1-8
AC K
DA TA
1-8
AC K
Stop
Figure 19. IC Write
SD A
SC L
00 10 00
A D 0
W
Sta rt
AC K
MA P
1- 8
AC K
00 10 00
A D 0
R
R e p e a te d ST AR T
or
A b o rte d W R IT E
AC K
Da ta 1 -8
(poi nted to by M A P )
D a ta 1 -8
(p oi nted to by M A P )
AC K
Sto p
Figure 20. IC Read
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B14-MV-F3 | CONVERTER MOD DC/DC 48V 150W |
| VE-B14-MV-F2 | CONVERTER MOD DC/DC 48V 150W |
| MS27497T18B11A | CONN HSG RCPT 11POS WALL MNT PIN |
| AD5541AARMZ | IC DAC 16BIT SERIAL IN 10MSOP |
| MS27508E12A4A | CONN HSG RCPT 4POS BOX MNT PIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS4360-DZZR | 功能描述:数模转换器- DAC IC 102dB 24Bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| CS4360-KS | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS4360-KZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cirrus Logic 功能描述:Digital Analog Converter, Hex, 24 Bit, 28 Pin, TSSOP |
| CS4360-KZZ | 功能描述:数模转换器- DAC IC 102dB 24Bit 192kHz 6 ch DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| CS4360-KZZR | 功能描述:数模转换器- DAC IC 102dB 24Bit 192kHz 6ch DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。