参数资料
| 型号： | CS53L21-CNZR |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 15/26页 |
| 文件大小： | 0K |
| 描述： | IC ADC STEREO 24BIT 98DB 32-QFN |
| 标准包装： | 6,000 |
| 位数： | 24 |
| 采样率（每秒）： | 100k |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 30mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -10°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-QFN |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 3 个单端，单极 |
| 配用： | 598-1550-ND - BOARD EVAL FOR CS53L21 ADC |
BU2280FV, BU2360FV, BU2362FV
Technical Note
22/23
www.rohm.com
2012.02 - Rev.B
2012 ROHM Co., Ltd. All rights reserved.
●Notes for use
1) Absolute Maximum Ratings
An excess in the absolute maximum ratings, such as applied voltage (VDD or VIN), operating temperature range (Topr),
etc., can break down devices, thus making impossible to identify breaking mode such as a short circuit or an open circuit.
If any special mode exceeding the absolute maximum ratings is assumed, consideration should be given to take physical
safety measures including the use of fuses, etc.
2) Recommended operating conditions
These conditions represent a range within which characteristics can be provided approximately as expected. The
electrical characteristics are guaranteed under the conditions of each parameter.
3) Reverse connection of power supply connector
The reverse connection of power supply connector can break down ICs. Take protective measures against the breakdown
due to the reverse connection, such as mounting an external diode between the power supply and the IC’s power supply
terminal.
4) Power supply line
Design PCB pattern to provide low impedance for the wiring between the power supply and the GND lines.
In this regard, for the digital block power supply and the analog block power supply, even though these power supplies has
the same level of potential, separate the power supply pattern for the digital block from that for the analog block, thus
suppressing the diffraction of digital noises to the analog block power supply resulting from impedance common to the
wiring patterns. For the GND line, give consideration to design the patterns in a similar manner.
Furthermore, for all power supply terminals to ICs, mount a capacitor between the power supply and the GND terminal. At
the same time, in order to use an electrolytic capacitor, thoroughly check to be sure the characteristics of the capacitor to be
used present no problem including the occurrence of capacity dropout at a low temperature, thus determining the constant.
5) GND voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
6) Short circuit between terminals and erroneous mounting
In order to mount ICs on a set PCB, pay thorough attention to the direction and offset of the ICs. Erroneous mounting can
break down the ICs. Furthermore, if a short circuit occurs due to foreign matters entering between terminals or between
the terminal and the power supply or the GND terminal, the ICs can break down.
7) Operation in strong electromagnetic field
Be noted that using ICs in the strong electromagnetic field can malfunction them.
8) Inspection with set PCB
On the inspection with the set PCB, if a capacitor is connected to a low-impedance IC terminal, the IC can suffer stress.
Therefore, be sure to discharge from the set PCB by each process. Furthermore, in order to mount or dismount the set
PCB to/from the jig for the inspection process, be sure to turn OFF the power supply and then mount the set PCB to the jig.
After the completion of the inspection, be sure to turn OFF the power supply and then dismount it from the jig. In addition,
for protection against static electricity, establish a ground for the assembly process and pay thorough attention to the
transportation and the storage of the set PCB.
9) Input terminals
In terms of the construction of IC, parasitic elements are inevitably formed in relation to potential. The operation of the
parasitic element can cause interference with circuit operation, thus resulting in a malfunction and then breakdown of the
input terminal. Therefore, pay thorough attention not to handle the input terminals, such as to apply to the input terminals a
voltage lower than the GND respectively, so that any parasitic element will operate. Furthermore, do not apply a voltage to
the input terminals when no power supply voltage is applied to the IC. In addition, even if the power supply voltage is
applied, apply to the input terminals a voltage lower than the power supply voltage or within the guaranteed value of
electrical characteristics.
10) Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the
small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
11) External capacitor
In order to use a ceramic capacitor as the external capacitor, determine the constant with consideration given to a
degradation in the nominal capacitance due to DC bias and changes in the capacitance due to temperature, etc.
相关PDF资料 |
PDF描述 |
|---|---|
| CS5509-ASZR | IC ADC 16BIT SGL SUPP 16-SOIC |
| CS5512-BSZ | IC ADC 20BIT EXTERNAL OSC 8-SOIC |
| CS5526-BSZR | IC ADC 20BIT W/4BIT LATCH 20SSOP |
| CS5528-ASZR | IC ADC 24BIT 8CH 24-SSOP |
| CS5529-ASZR | IC ADC 16BIT W/6BIT LATCH 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CS53L21-DNZ | 制造商:Cirrus Logic 功能描述:IC LW-POWER STEREO ANALOG-TO-DIGITAL ADC - Rail/Tube 制造商:Cirrus Logic 功能描述:IC ADC STEREO 24BIT 96KHZ 32QFN |
| CS53L21-DNZR | 制造商:Cirrus Logic 功能描述:IC LW-POWER STEREO ANALOG-TO-DIGITAL ADC - Tape and Reel 制造商:Cirrus Logic 功能描述:IC ADC STEREO 24BIT 96KHZ 32QFN |
| CS53L30-CNZ | 制造商:Cirrus Logic 功能描述:IC ADC 24BIT STER 16KHZ 32QFN 制造商:Cirrus Logic 功能描述:Audio A/D Converter ICs 4 Mic ADC 制造商:Cirrus Logic 功能描述:ADC, 24BIT, 16KSPS, I2C, QFN-32, Resolution (Bits):24bit, Sampling Rate:16kSPS, |
| CS53L30-CNZR | 功能描述:IC ADC 24BIT STER 16KHZ 32QFN 制造商:cirrus logic inc. 系列:- 包装:带卷（TR） 零件状态:在售 类型:ADC，音频 分辨率（位）:24 b 采样率（每秒）:16k 数据接口:I2S 电压源:单电源 电压 - 电源:1.71 V ~ 1.89 V 工作温度:-10°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商器件封装:32-QFN（5x5） 基本零件编号:CS53L30 标准包装:6,000 |
| CS53L30-CWZR | 功能描述:音频模/数转换器 IC 4 Mic ADC RoHS:否 制造商:Wolfson Microelectronics 转换速率: 分辨率: ADC 输入端数量: 工作电源电压: 最大工作温度: 最小工作温度: 安装风格: 封装 / 箱体: 封装: |
发布紧急采购，3分钟左右您将得到回复。