- 您现在的位置：买卖IC网 > PDF目录21889 > CUB5SNK0 (Red Lion Controls)DUAL SINKING OPEN OC OUT CARD PDF资料下载
参数资料
| 型号： | CUB5SNK0 |
| 厂商： | Red Lion Controls |
| 文件页数： | 4/16页 |
| 文件大小： | 0K |
| 描述： | DUAL SINKING OPEN OC OUT CARD |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | RLC165 |
3.0 I NSTALLING P LUG -I N C ARDS
The Plug-in cards are separately purchased option cards that perform specific
functions. The cards plug into the main circuit board of the meter. After
installing the cards, replace the rear cover before wiring the meter.
CAUTION: The Plug-in cards and main circuit board contain static
sensitive components. Before handling the cards, discharge
static charges from your body by touching a grounded bare
metal object. Ideally, handle the cards at a static controlled
clean workstation. Also, only handle the cards by the edges.
Dirt, oil or other contaminants that may contact the cards can
adversely affect circuit operation.
Comms or
Programming
Card
1
ON
2
ECE
3 4
Setpoint Card
REPLACING THE REAR COVER
To replace the rear cover, align the cover with the input terminals and press
down until the cover snaps into place.
Locking Tab
4.0 W IRING
THE
M ETER
}
WIRING OVERVIEW
Electrical connections are made via screw-clamp terminals located on the
back of the meter. All conductors should conform to the meter ’s voltage and
current ratings. All cabling should conform to appropriate standards of good
installation, local codes and regulations. It is recommended that the power
supplied to the meter (DC or AC) be protected by a fuse or circuit breaker.
Strip the wire, leaving approximately 0.3" (7.5 mm) bare lead exposed
(stranded wires should be tinned with solder.) Insert the lead under the correct
screw-clamp terminal and tighten until the wire is secure. (Pull wire to verify
tightness.) Each terminal can accept up to one #14 AWG (2.55 mm) wire, two
#18 AWG (1.02 mm), or four #20 AWG (0.61 mm).
EMC INSTALLATION GUIDELINES
Although this meter is designed with a high degree of immunity to Electro-
Magnetic Interference (EMI), proper installation and wiring methods must be
followed to ensure compatibility in each application. The type of the electrical
noise, source or coupling method into the meter may be different for various
installations. The meter becomes more immune to EMI with fewer I/O
connections. Cable length, routing, and shield termination are very important
and can mean the difference between a successful or troublesome installation.
Listed below are some EMC guidelines for successful installation in an
industrial environment.
1. The meter should be mounted in a metal enclosure, which is properly
connected to protective earth.
2. Use shielded (screened) cables for all Signal and Control inputs. The shield
(screen) pigtail connection should be made as short as possible. The
connection point for the shield depends somewhat upon the application.
Listed below are the recommended methods of connecting the shield, in order
of their effectiveness.
a. Connect the shield only at the panel where the unit is mounted to earth
ground (protective earth).
b. Connect the shield to earth ground at both ends of the cable, usually when
the noise source frequency is above 1 MHz.
4.1 POWER WIRING
DC Power
+9 to +28 VDC: +VDC
Power Common: -VDC
c. Connect the shield to common of the meter and leave the other end of the
shield unconnected and insulated from earth ground.
3. Never run Signal or Control cables in the same conduit or raceway with AC
power lines, conductors feeding motors, solenoids, SCR controls, and
heaters, etc. The cables should be ran in metal conduit that is properly
grounded. This is especially useful in applications where cable runs are long
and portable two-way radios are used in close proximity or if the installation
is near a commercial radio transmitter.
4. Signal or Control cables within an enclosure should be routed as far as possible
from contactors, control relays, transformers, and other noisy components.
5. In extremely high EMI environments, the use of external EMI suppression
devices, such as ferrite suppression cores, is effective. Install them on Signal
and Control cables as close to the unit as possible. Loop the cable through the
core several times or use multiple cores on each cable for additional protection.
Install line filters on the power input cable to the unit to suppress power line
interference. Install them near the power entry point of the enclosure. The
following EMI suppression devices (or equivalent) are recommended:
Ferrite Suppression Cores for signal and control cables:
Fair-Rite # 0443167251 (RLC# FCOR0000)
TDK # ZCAT3035-1330A
Steward # 28B2029-0A0
Line Filters for input power cables:
Schaffner # FN610-1/07 (RLC# LFIL0000)
Schaffner # FN670-1.8/07
Corcom # 1 VR3
Note: Reference manufacturer ’s instructions when installing a line filter.
6. Long cable runs are more susceptible to EMI pickup than short cable runs.
Therefore, keep cable runs as short as possible.
7. Switching of inductive loads produces high EMI. Use of snubbers across
inductive loads suppresses EMI.
Snubber: RLC# SNUB0000.
4.2 USER INPUT WIRING
Sinking Logic
INP COMM Connect external switching device between the
USR User Input terminal and Input Common.
The user input of the meter is
internally pulled up to +9 to +28 V
with 10 K resistance. The input is
active when it is pulled low (<1 .0 V).
PWR COMMON
-
+
+9-28 VDC
4
PWR COMMON
+9-28 VDC
相关PDF资料 |
PDF描述 |
|---|---|
| MLBAWT-A1-0000-000W50 | LED XLAMP ML-B WHITE SMD |
| MLBAWT-A1-0000-000VF8 | LED XLAMP ML-B WHITE SMD |
| MLBAWT-A1-0000-000VF7 | LED XLAMP ML-B WHITE SMD |
| ACA-20RM-5-AC4-RL-ALM-C | AMMETER AC 30A 220V W/ALARM RED |
| MLBAWT-A1-0000-000VF5 | LED XLAMP ML-B WHITE SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CUB5TB00 | 功能描述:TIMER & CYCLE COUNTER W/BKLT RoHS:是 类别:工业控制，仪表 >> 计数器 系列:* 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮 |
| CUB5TCB0 | 功能描述:METER PANEL LCD THERMOCOUPLE RED RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:CUB5 标准包装:12 系列:* 其它名称:Q7072030 |
| CUB5TCR0 | 功能描述:THERMO METER REFLECTIVE RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030 |
| CUB5TR00 | 制造商:Red Lion Controls 功能描述:PRESET TIMR & CYCLE COUNTR W/REFL DSPLY 制造商:Red Lion Controls 功能描述:TIMER, ELECTRONIC , 8DIGIT, 9V TO 28V; Supply Voltage Range:9V DC to 28V DC; Panel Cutout Height:39.1mm; Panel Cutout Width:74.9mm; Time Range:- ;RoHS Compliant: Yes |
| CUB5USB0 | 功能描述:USB OPTION CARD RoHS:是 类别:工业控制，仪表 >> 仪表 - 面板，数字 系列:* 标准包装:12 系列:* 其它名称:Q7072030 |
发布紧急采购，3分钟左右您将得到回复。