- 您现在的位置：买卖IC网 > PDF目录17091 > DAC5674EVM (Texas Instruments)EVAL MODULE FOR DAC5674 PDF资料下载
参数资料
| 型号： | DAC5674EVM |
| 厂商： | Texas Instruments |
| 文件页数： | 20/39页 |
| 文件大小： | 0K |
| 描述： | EVAL MODULE FOR DAC5674 |
| 产品培训模块： | Data Converter Basics |
| 标准包装： | 1 |
| 系列： | CommsDAC™ |
| DAC 的数量： | 1 |
| 位数： | 14 |
| 采样率（每秒）： | 400M |
| 数据接口： | 并联 |
| 设置时间： | 20ns |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | DAC5674 |
| 相关产品： | DAC5674IPHPRG4-ND - IC DAC 14BIT 400MSPS 48-HTQFP DAC5674IPHPR-ND - IC DAC 14BIT 400MSPS 48-HTQFP DAC5674IPHPG4-ND - IC DAC 14BIT 400MSPS 48-HTQFP 296-15726-ND - IC DAC 14BIT 400MSPS 48-HTQFP |
| 其它名称： | 296-30860 DAC5674EVM-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
DAC5674
SLWS148A SEPTEMBER 2003 REVISED OCTOBER 2005
www.ti.com
27
VOUT1
+ IOUT1
R
L + IOUTFS
CODE
16384
R
L
VOUT2
+ IOUT2
R
L + IOUTFS
16383
* CODE
16384
R
L
The differential output voltage VOUTDIFF can thus be expressed as:
VOUT
DIFF + VOUT1 * VOUT2 + IOUTFS
2CODE
* 16383
16384
R
L
The latter equation shows that applying the differential output results in doubling of the signal power delivered
to the load. Because the output currents IOUT1 and IOUT2 are complementary, they become additive when
processed differentially. Note that care should be taken not to exceed the compliance voltages at node IOUT1
and IOUT2, which would lead to increased signal distortion.
Reference Operation
The DAC5674 comprises a band-gap reference and control amplifier for biasing the full-scale output current.
The full-scale output current is set by applying an external resistor RBIAS. The bias current IBIAS through resistor
RBIAS is defined by the on-chip band-gap reference voltage and control amplifier. The full-scale output current
equals 32 times this bias current. The full-scale output current IOUTFS can thus be expressed as:
IOUT
FS +
32
I
BIAS +
32
V
EXTIO
R
BIAS
where VEXTIO is the voltage at terminal EXTIO. The band-gap reference voltage delivers an accurate voltage
of 1.2 V. This reference is active when terminal EXTLO is connected to AGND. An external decoupling capacitor
CEXT of 0.1 F should be connected externally to terminal EXTIO for compensation. The band-gap reference
can additionally be used for external reference operation. In that case, an external buffer with high impedance
input should be applied in order to limit the band-gap load current to a maximum of 100 nA. The internal
reference can be disabled and overridden by an external reference by connecting EXTLO to AVDD. In this case,
capacitor CEXT can be omitted. Terminal EXTIO serves as either input or output node.
The full-scale output current can be adjusted from 20 mA to 2 mA by varying resistor RBIAS or changing the
externally applied reference voltage. The internal control amplifier has a wide input range, supporting the
full-scale output current range of 20 mA.
Analog Current Outputs
Figure 34 shows a simplified schematic of the current source array output with corresponding switches.
Differential switches direct the current of each individual PMOS current source to either the positive output node
IOUT1 or its complementary negative output node IOUT2. The output impedance is determined by the stack
of the current sources and differential switches, and is typically >300 k
in parallel with an output capacitance
of 5 pF.
The external output resistors are referred to an external ground. The minimum output compliance at nodes
IOUT1 and IOUT2 is limited to 1 V, determined by the CMOS process. Beyond this value, transistor breakdown
may occur resulting in reduced reliability of the DAC5674 device. The maximum output compliance voltage at
nodes IOUT1 and IOUT2 equals 1.25 V. Exceeding the maximum output compliance voltage adversely affects
distortion performance and integral nonlinearity. The optimum distortion performance for a single-ended or
differential output is achieved when the maximum full-scale signal at IOUT1 and IOUT2 does not exceed 0.5 V.
相关PDF资料 |
PDF描述 |
|---|---|
| ELJ-PE5N6KF | INDUCTOR 5.6NH 10% 0603 SMD |
| ECM15DSEN-S13 | CONN EDGECARD 30POS .156 EXTEND |
| AP2280-1FMG-7 | IC LOAD SW CTRL 1CH 6-DFN |
| SDR-X | SCOTCH CODE REFILL X |
| ECM15DSEH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DAC5674IPHP | 功能描述:数模转换器- DAC 14-Bit 400 CommsDAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| DAC5674IPHPG4 | 功能描述:数模转换器- DAC 14-Bit 400 CommsDAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| DAC5674IPHP-ND | 制造商: 功能描述: 制造商:undefined 功能描述: |
| DAC5674IPHPR | 功能描述:数模转换器- DAC 14-Bit 400 CommsDAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| DAC5674IPHPRG4 | 功能描述:数模转换器- DAC 14-Bit 400 CommsDAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。