- 您现在的位置：买卖IC网 > PDF目录17064 > DC1009A-B (Linear Technology)BOARD DELTA SIGMA ADC LTC2488 PDF资料下载
参数资料
| 型号： | DC1009A-B |
| 厂商： | Linear Technology |
| 文件页数： | 4/30页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2488 |
| 软件下载： | QuikEval System |
| 设计资源： | DC1009A Design File DC1009A Schematic |
| 标准包装： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 6.9 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2488 |
| 已供物品： | 板 |
| 相关产品： | LTC2488CDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488CDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC2488
12
2488fa
APPLICATIONS INFORMATION
enables external RC networks and high impedance sen-
sors to directly interface to the LTC2488 without external
ampliers. The remaining common mode input current
is eliminated by either balancing the differential input
impedances or setting the common mode input equal to
the common mode reference (see Automatic Differential
Input Current Cancellation Section). This unique architec-
ture does not require on-chip buffers, thereby enabling
signals to swing beyond ground and VCC. Moreover, the
cancellation does not interfere with the transparent offset
and full-scale auto-calibration and the absolute accuracy
(full scale + offset + linearity + drift) is maintained even
with external RC networks.
Power-Up Sequence
The LTC2488 automatically enters an internal reset state
when the power supply voltage VCC drops below ap-
proximately 2V. This feature guarantees the integrity of
the conversion result, input channel selection, and serial
clock mode.
When VCC rises above this threshold, the converter creates
an internal power-on-reset (POR) signal with a duration
of approximately 4ms. The POR signal clears all internal
registers. The conversion immediately following a POR
cycle is performed on the input channel IN+ = CH0, IN– =
CH1. The rst conversion following a POR cycle is accurate
within the specication of the device if the power supply
voltage is restored to (2.7V to 5.5V) before the end of the
POR interval. A new input channel can be programmed into
the device during this rst data input/output cycle.
Reference Voltage Range
This converter accepts a truly differential external reference
voltage. The absolute/common mode voltage range for
REF+ and REF– pins covers the entire operating range of
the device (GND to VCC). For correct converter operation,
VREF must be positive (REF+ > REF–).
The LTC2488 differential reference input range is 0.1V to
VCC. For the simplest operation, REF+ can be shorted to VCC
and REF– can be shorted to GND. The converter output noise
is determined by the thermal noise of the front end circuits.
Since the transition noise is well below 1LSB (0.02LSB), a
decrease in reference voltage will proportionally improve
the converter resolution and improve INL.
Input Voltage Range
The analog inputs are truly differential with an absolute,
common mode range for the CH0 to CH3 and COM input
pins extending from GND – 0.3V to VCC + 0.3V. Outside
these limits, the ESD protection devices begin to turn
on and the errors due to input leakage current increase
rapidly. Within these limits, the LTC2488 converts the
bipolar differential input signal VIN = IN+ – IN– (where
IN+ and IN– are the selected input channels), from –FS =
–0.5 VREF to +FS = 0.5 VREF where VREF = REF+ – REF–.
Outside this range, the converter indicates the overrange
or the underrange condition using distinct output codes
(see Table 1).
Signals applied to the input (CH0 to CH3, COM) may
extend 300mV below ground and above VCC. In order to
limit any fault current, resistors of up to 5k may be added
in series with the input. The effect of series resistance on
the converter accuracy can be evaluated from the curves
presented in the Input Current/Reference Current sections.
In addition, series resistors will introduce a temperature
dependent error due to input leakage current. A 1nA input
leakage current will develop a 1ppm offset error on a 5k
resistor if VREF = 5V. This error has a very strong tem-
perature dependency.
SERIAL INTERFACE PINS
The LTC2488 transmits the conversion result, reads the
input channel selection, and receives a start of conversion
command through a synchronous 3- or 4-wire interface.
During the conversion and sleep states, this interface can
be used to access the converter status. During the data
output state, it is used to read the conversion result and
program the input channel.
Serial Clock Input/Output (SCK)
The serial clock pin (SCK) is used to synchronize the data
input/output transfer. Each bit is shifted out of the SDO
pin on the falling edge of SCK and data is shifted into the
SDI pin on the rising edge of SCK.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9787-DPG2-EBZ | BOARD EVALUATION FOR AD9787 |
| ESA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| SDR0604-331KL | INDUCTOR POWER 330UH 10% SMD |
| AD9788-DPG2-EBZ | BOARD EVALUATION FOR AD9788 |
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1009A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2486 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC100A10 | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A10C | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A20 | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A20C | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
发布紧急采购，3分钟左右您将得到回复。