- 您现在的位置：买卖IC网 > PDF目录17064 > DC1009A-B (Linear Technology)BOARD DELTA SIGMA ADC LTC2488 PDF资料下载
参数资料
| 型号： | DC1009A-B |
| 厂商： | Linear Technology |
| 文件页数： | 5/30页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2488 |
| 软件下载： | QuikEval System |
| 设计资源： | DC1009A Design File DC1009A Schematic |
| 标准包装： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 6.9 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2488 |
| 已供物品： | 板 |
| 相关产品： | LTC2488CDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488CDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC2488
13
2488fa
APPLICATIONS INFORMATION
The serial clock pin (SCK) can be congured as either a
master (SCK is an output generated internally) or a slave
(SCK is an input and applied externally). Master mode
(Internal SCK) is selected by simply oating the SCK pin.
Slave mode (External SCK) is selected by driving SCK low
during power up and each falling edge of CS. Specic
details of these SCK modes are described in the Serial
Interface Timing Modes section.
Serial Data Output (SDO)
The serial data output pin (SDO) provides the result of the
last conversion as a serial bit stream (MSB rst) during
the data output state. In addition, the SDO pin is used as
an end of conversion indicator during the conversion and
sleep states.
When CS is HIGH, the SDO driver is switched to a high
impedance state in order to share the data output line with
other devices. If CS is brought LOW during the conversion
phase, the EOC bit (SDO pin) will be driven HIGH. Once the
conversion is complete, if CS is brought LOW, EOC will be
driven LOW indicating the conversion is complete and the
result is ready to be shifted out of the device.
Chip Select (CS)
The active low CS pin is used to test the conversion status,
enable I/O data transfer, initiate a new conversion, control
the duration of the sleep state, and set the SCK mode.
At the conclusion of a conversion cycle, while CS is HIGH,
the device remains in a low power sleep state where the
supply current is reduced several orders of magnitude. In
order to exit the sleep state and enter the data output state,
CS must be pulled low. Data is now shifted out the SDO pin
under control of the SCK pin as described previously.
A new conversion cycle is initiated either at the conclusion
of the data output cycle (all 24 data bits read) or by pulling
CS HIGH any time between the rst and 24th rising edges
of the serial clock (SCK). In this case, the data output is
aborted and a new conversion begins.
Serial Data Input (SDI)
The serial data input (SDI) is used to select the input
channel. Data is shifted into the device during the data
output/input state on the rising edge of SCK while CS is
low.
OUTPUT DATA FORMAT
The LTC2488 serial output stream is 24 bits long. The
rst bit indicates the conversion status, the second bit is
always zero, and the third bit conveys sign information.
The next 17 bits are the conversion result, MSB rst. The
remaining 4 bits are always LOW.
Bit 23 (rst output bit) is the end of conversion (EOC)
indicator. This bit is available on the SDO pin during the
conversion and sleep states whenever CS is LOW. This
bit is HIGH during the conversion cycle, goes LOW once
the conversion is complete, and is HIGH-Z when CS is
HIGH.
Bit 22 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 21 (third output bit) is the conversion result sign
indicator (SIG). If the selected input (VIN = IN+ – IN–) is
greater than or equal to 0V, this bit is HIGH. If VIN < 0,
this bit is LOW.
Bit 20 (fourth output bit) is the most signicant bit (MSB)
of the result. This bit in conjunction with Bit 21 also pro-
vides underrange and overrange indication. If both Bit 21
and Bit 20 are HIGH, the differential input voltage is above
+FS. If both Bit 21 and Bit 20 are LOW, the differential
input voltage is below –FS. The function of these bits is
summarized in Table 1.
Table 1. LTC2488 Status Bits
Input Range
Bit 23
EOC
Bit 22
DMY
Bit 21
SIG
Bit 20
MSB
VIN ≥ 0.5 VREF
0011
0V ≤ VIN < 0.5 VREF
0010
–0.5 VREF ≤ VIN < 0V
0001
VIN < –0.5 VREF
0000
Bits 20 to 4 are the 16-bit plus sign conversion result
MSB rst.
Bit 4 is the least signicant bit (LSB16).
Bits 3 to 0 are always LOW.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9787-DPG2-EBZ | BOARD EVALUATION FOR AD9787 |
| ESA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| SDR0604-331KL | INDUCTOR POWER 330UH 10% SMD |
| AD9788-DPG2-EBZ | BOARD EVALUATION FOR AD9788 |
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1009A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2486 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC100A10 | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A10C | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A20 | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A20C | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
发布紧急采购，3分钟左右您将得到回复。