- 您现在的位置：买卖IC网 > PDF目录17064 > DC1009A-B (Linear Technology)BOARD DELTA SIGMA ADC LTC2488 PDF资料下载
参数资料
| 型号： | DC1009A-B |
| 厂商： | Linear Technology |
| 文件页数： | 9/30页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2488 |
| 软件下载： | QuikEval System |
| 设计资源： | DC1009A Design File DC1009A Schematic |
| 标准包装： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 6.9 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2488 |
| 已供物品： | 板 |
| 相关产品： | LTC2488CDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#TRPBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488CDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN LTC2488IDE#PBF-ND - IC ADC 16BIT DELTA SIG 14-DFN |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC2488
17
2488fa
state. However, the data output state may be aborted by
pulling CS HIGH any time between the 1st falling edge
and the 24th falling edge of SCK (see Figure 5). On the
rising edge of CS, the device aborts the data output state
and immediately initiates a new conversion. In order to
program a new input channel, 8 SCK clock pulses are
required. If the data output sequence is aborted prior to
the 8th falling edge of SCK, the new input data is ignored
and the previously selected input channel remains valid.
If the rising edge of CS occurs after the 8th falling edge
of SCK, the new input channel is loaded and valid for the
next conversion cycle.
External Serial Clock, 3-Wire I/O
This timing mode uses a 3-wire serial I/O interface. The
conversion result is shifted out of the device by an exter-
nally generated serial clock (SCK) signal (see Figure 6).
CS is permanently tied to ground, simplifying the user
interface or isolation barrier.
The external serial clock mode is selected at the end of
the power-on reset (POR) cycle. The POR cycle typically
concludes 4ms after VCC exceeds 2V. The level applied to
SCK at this time determines if SCK is internally generated
or externally applied. In order to enter the external SCK
mode, SCK must be driven LOW prior to the end of the
POR cycle.
Since CS is tied LOW, the end-of-conversion (EOC) can be
continuously monitored at the SDO pin during the convert
and sleep states. EOC may be used as an interrupt to an
external controller. EOC = 1 while the conversion is in
progress and EOC = 0 once the conversion is complete.
On the falling edge of EOC, the conversion result is load-
ing into an internal static shift register. The output data
can now be shifted out the SDO pin under control of the
externally applied SCK signal. Data is updated on the fall-
ing edge of SCK. The input data is shifted into the device
through the SDI pin on the rising edge of SCK. On the
24th falling edge of SCK, SDO goes HIGH, indicating a
new conversion has begun. This data now serves as EOC
for the next conversion.
APPLICATIONS INFORMATION
VCC
FO
SCK
SDI
GND
6
REFERENCE
VOLTAGE
0.1V TO VCC
ANALOG
INPUTS
= EXTERNAL OSCILLATOR
= INTERNAL OSCILLATOR
LTC2488
4-WIRE
SPI INTERFACE
REF+
REF–
CH0
CH1
CH2
CH3
COM
CS
SDO
12
1
13
14
8
9
10
11
7
3
4
5
2
2.7V TO 5.5V
0.1μF
10μF
Hi-Z
2488 F05
CS
SCK
(EXTERNAL)
SDI
SDO
CONVERSION
SLEEP
DATA INPUT/OUTPUT
SLEEP
CONVERSION
EOC
BIT 20 BIT 19 BIT 18 BIT 17 BIT 16
BIT 15
BIT 21
BIT 22
BIT 23
12
3
4
5
6
7
8
1
0
EN
SGL
A2
A1
A0
ODD
DON'T CARE
MSB
SIG
“0”
Figure 5. External Serial Clock, Reduced Output Data Length and Valid Channel Selection
相关PDF资料 |
PDF描述 |
|---|---|
| AD9787-DPG2-EBZ | BOARD EVALUATION FOR AD9787 |
| ESA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| SDR0604-331KL | INDUCTOR POWER 330UH 10% SMD |
| AD9788-DPG2-EBZ | BOARD EVALUATION FOR AD9788 |
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1009A-C | 功能描述:BOARD DELTA SIGMA ADC LTC2486 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:Easy Drive™, QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC100A10 | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A10C | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 10A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A20 | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| DC100A20C | 功能描述:固态继电器-工业安装 SSR DC OUTPUT 20A 90-140VAC RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
发布紧急采购，3分钟左右您将得到回复。