- 您现在的位置：买卖IC网 > PDF目录20391 > DC1453A (Linear Technology)BOARD EVAL LTM4619 PDF资料下载
参数资料
| 型号： | DC1453A |
| 厂商： | Linear Technology |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LTM4619 |
| 软件下载： | LTM4619 Spice Model |
| 设计资源： | DC1453A Design Files DC1453A Schematic |
| 标准包装： | 1 |
| 系列： | LTM®, uModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 2，非隔离 |
| 输出电压： | 1.8V，3.3V |
| 电流 - 输出： | 4A |
| 输入电压： | 4.5 ~ 28 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 500kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4619 |
| 相关产品： | LTM4619IV#PBF-ND - IC SWIT REG BUCK 4A ADJ 144LGA LTM4619EV#PBF-ND - IC SWIT REG BUCK 4A ADJ 144LGA |
LTM4619
PIN FUNCTIONS
1– OUT ? V OUT
FREQ ? V IN ?
I RIPPLE =
PACKAGEROWANDCOLUMNLABELINGMAYVARY
AMONG μModule PRODUCTS. REVIEW EACH PACKAGE
LAYOUT CAREFULLY.
V IN (J1 to J3, J10 to J12, K1 to K4, K9 to K12, L1 to L5,
L8 to L12, M1 to M12): Power Input Pins. Apply input
voltage between these pins and PGND pins. Recommend
placing input decoupling capacitance directly between V IN
pins and PGND pins. For V IN < 5.5, tie V IN and INTV CC
together.
V OUT1 , V OUT2 (A10 to D10, A11 to D11, A12 to D12, A1 to
D1, A2 to D2, A3 to D3): Power Output Pins. Apply output
load between these pins and PGND pins. Recommend
placing output decoupling capacitance directly between
these pins and PGND pins.
PGND (H1, H2, H4, H9, H11, H12, G1 to G12, F1 to F5,
F7 to F12, E1 to E12, D4 to D9, C4 to C9, B4 to B9, A4 to
A9): Power ground pins for both input and output returns.
INTV CC (F6): Internal 5V Regulator Output. This pin is for
additional decoupling of the 5V internal regulator.
EXTV CC (J4): External Power Input to Controller. When
EXTV CC is higher than 4.7V, the internal 5V regulator is
disabled and external power supplies current to reduce
the power dissipation in the module. This will improve the
efficiency more at high input voltages.
SGND (J6, J7, H6, H7): Signal Ground Pin. Return ground
path for all analog and low power circuitry. Tie a single
connection to PGND in the application.
MODE/PLLIN (H8): Mode selection or external synchroniza-
tion pin. Tying this pin high enables pulse-skipping mode.
Tying this pin low enables force continuous operation.
Floating this pin enables Burst Mode operation. A clock
on the pin will force the controller into the continuous
mode of operation and synchronize the internal oscillator.
The suitable synchronizable frequency range is 250kHz to
780kHz subject to inductor ripple current limits described
in the FREQ/PLLFLTR pin section. The external clock input
high threshold is 1.6V, while the input low threshold is 1V.
FREQ/PLLFLTR (J8): Frequency Selection Pin. An internal
lowpass filter is tied to this pin. The frequency can be
selected from 250kHz to 780kHz by varying the DC volt-
age on this pin from 0V to 2.4V. The nominal frequency
setting is 500kHz. Frequency selection can be modified as
long as the inductor ripple current is less ≈40% to 50%
at the output current
1 ? V ?
L
Where FREQ is selected operating frequency and L is
the inductor value. Leave this pin floating when external
synchronization is used.
TK/SS1, TK/SS2 (K8, K5): Output Voltage Tracking and
Soft-Start Pins. Internal soft-start currents of 1.3μA charge
the soft-start capacitors. See the Applications Information
section to use the tracking function.
V FB1 , V FB2 (K7, K6): The negative input of the error
amplifier. Internally, this pin is connected to V OUT with
a 60.4k precision resistor. Different output voltages can
be programmed with an additional resistor between V FB
and SGND pins. See the Applications Information section
for details.
COMP1, COMP2 (L7, L6 ): Current Control Threshold and
Error Amplifier Compensation Point. The module has been
internally compensated for most I/O ranges.
PGOOD (H5): Output Voltage Power Good Indicator. Open
drain logic output that is pulled to ground when the output
voltage is not within ±7.5% of the regulation point.
RUN1, RUN2 (J9, J5): Run Control Pins. 0.5μA pull-up
currents on these pins turn on the module if these pins
are floating. Forcing either of these pins below 1.2V will
shut down the corresponding outputs. An additional 4.5μA
pull-up current is added to this pin, once the RUN pin rises
above 1.2V. Also, active control or pull-up resistors can
be used to enable the RUN pin. The maximum voltage is
6V on these pins.
SW1, SW2 (H10, H3): Switching Test Pins. These pins
are provided externally to check the operation frequency.
4619fb
6
For more information www.linear.com/LTM4619
相关PDF资料 |
PDF描述 |
|---|---|
| IR2153STR | IC DRVR HALF BRDG SELF-OSC 8SOIC |
| EL7158IS-T13 | IC PIN DRIVER 40MHZ 3ST 8-SOIC |
| RY-1215S | CONV DC/DC 1W 12VIN 15VOUT |
| R0.25D12-3.305/H-R | CONV DC/DC 0.25W 3.3VIN +/-5VOUT |
| EYM08DTAD-S189 | CONN EDGECARD 16POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1459A | 功能描述:BOARD EVALUATION FOR LTC3588 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
| DC1459B-A | 制造商:Linear Technology 功能描述:ENERY HARVESTING EVAL. BOARD 制造商:Linear Technology 功能描述:LTC3588, ENERGY HARVESTING PWR SUPPLY, DEMO BOARD; Silicon Manufacturer:Linear Technology; Kit Application Type:Power Management; Application Sub Type:Energy Harvesting; Kit Contents:Board |
| DC1459B-B | 制造商:Linear Technology 功能描述:EVAL BOARD, LTC3588 ENERGY HARVESTING PO 制造商:Linear Technology 功能描述:EVAL BOARD, LTC3588 ENERGY HARVESTING POWER SUPPLY; Silicon Manufacturer:Linear Technology; Silicon Core Number:LTC3588; Kit Application Type:Power Management; Application Sub Type:Energy Harvesting; Kit Contents:Board, Guide |
| DC1460A | 制造商:Linear Technology 功能描述:EVAL BOARD, LTC3620 BUCK REGULATOR, Silicon Manufacturer:Linear Technology, Sili |
| DC1466A-A | 功能描述:BOARD DAC LTC2636-12 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:QuikEval™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。