- 您现在的位置：买卖IC网 > PDF目录16760 > DC1568A (Linear Technology)BOARD BATTERY CHARGER SOLAR PWR PDF资料下载
参数资料
| 型号： | DC1568A |
| 厂商： | Linear Technology |
| 文件页数： | 19/26页 |
| 文件大小： | 0K |
| 描述： | BOARD BATTERY CHARGER SOLAR PWR |
| 视频文件： | Linear Technology LT3652 |
| 设计资源： | DC1568A Design Files DC1568A Schematic |
| 特色产品： | Energy Harvesting Power Products |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LT3652 |
| 主要属性： | 多种化学，太阳能 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板 |
| 相关产品： | LT3652HVIMSE#TRPBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVIMSE#PBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVIDD#TRPBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVIDD#PBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEMSE#TRPBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVEDD#TRPBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEDD#PBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEMSE#PBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652IMSE#TRPBF-ND - IC BATT CHARGER SOLAR 2A 12MSOP LT3652IMSE#PBF-ND - IC BATT CHARGER SOLAR 2A 12MSOP 更多... |
LT3652
APPLICATIONS INFORMATION
Status Pins
The LT3652 reports charger status through two open
collector outputs, the CHRG and FAULT pins. These pins
can accept voltages as high as V IN , and can sink up to
10mA when enabled.
The CHRG pin indicates that the charger is delivering
current at greater that a C/10 rate, or 1/10th of the pro-
grammed maximum charge current. The FAULT pin signals
bad battery and NTC faults. These pins are binary coded,
and signal following the table below, where ON indicates
pin pulled low, and OFF indicates pin high-impedance:
STATUS PINS STATE
When C/10 termination is used, a LT3652 charger will
source battery charge current as long as the average
current level remains above the C/10 threshold. As the
full-charge float voltage is achieved, the charge current
falls until the C/10 threshold is reached, at which time the
charger terminates and the LT3652 enters standby mode.
The CHRG status pin follows the charger cycle, and is high
impedance when the charger is not actively charging.
When V BAT drops below 97.5% of the full-charged float
voltage, whether by battery loading or replacement of the
battery, the charger automatically re-engages and starts
charging.
There is no provision for bad battery detection if C/10
termination is used.
CHRG
FAULT
CHARGER STATUS
OFF
OFF
ON
ON
OFF
ON
OFF
ON
Not Charging — Standby or Shutdown Mode
Bad Battery Fault (Precondition Timeout / EOC
Failure)
Normal Charging at C/10 or Greater
NTC Fault (Pause)
Timer Termination
The LT3652 supports a timer based termination scheme, in
which a battery charge cycle is terminated after a specific
amount of time elapses. Timer termination is engaged
when a capacitor (C TIMER ) is connected from the TIMER
pin to ground. The timer cycle EOC (T EOC ) occurs based
If the battery is removed from an LT3652 charger that is
configured for C/10 termination, a sawtooth waveform
on C TIMER following the relation:
of approximately 100mV appears at the charger output,
due to cycling between termination and recharge events,
This cycling results in pulsing at the CHRG output. An
C TIMER = T EOC ? 2.27 x 10 –7
(Hours)
LED connected to this pin will exhibit a blinking pattern,
indicating to the user that a battery is not present. The
frequency of this blinking pattern is dependent on the
output capacitance.
C/10 Termination
The LT3652 supports a low-current based termination
scheme, where a battery charge cycle terminates when the
current output from the charger falls to below one-tenth
of the maximum current, as programmed with R SENSE .
The C/10 threshold current corresponds to 10mV across
R SENSE . This termination mode is engaged by shorting
the TIMER pin to ground.
Timer EOC is typically set to 3 hours, which requires a
0.68μF capacitor.
The CHRG status pin continues to signal charging at a C/10
rate, regardless of what termination scheme is used. When
timer termination is used, the CHRG status pin is pulled
low during a charging cycle until the charger output cur-
rent falls below the C/10 threshold. The charger continues
to top-off the battery until timer EOC, when the LT3652
terminates the charging cycle and enters standby mode.
Termination at the end of the timer cycle only occurs if
the charging cycle was successful. A successful charge
cycle is when the battery is charged to within 2.5% of the
3652fd
19
相关PDF资料 |
PDF描述 |
|---|---|
| GBB15DHHT | CONN EDGECARD 30POS .050 DIP SLD |
| GBM25DTBH-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| RT-375-1/16-X-SP-SM | HEAT SHRINK TUBING |
| RNF-100-3/8-GN-STK | HEAT SHRINK TUBING |
| GBM25DTBD-S189 | CONN EDGECARD 50POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1568A | 制造商:Linear Technology 功能描述:BATTERY CHARGER DEMO. BOARD ((NW)) |
| DC1571A-A | 功能描述:BOARD SAR ADC LTC2383-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571A-B | 功能描述:BOARD SAR ADC LTC2382-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571A-C | 功能描述:BOARD SAR ADC LTC2381-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571B | 制造商:Aleph America Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。