- 您现在的位置：买卖IC网 > PDF目录16760 > DC1568A (Linear Technology)BOARD BATTERY CHARGER SOLAR PWR PDF资料下载
参数资料
| 型号： | DC1568A |
| 厂商： | Linear Technology |
| 文件页数： | 20/26页 |
| 文件大小： | 0K |
| 描述： | BOARD BATTERY CHARGER SOLAR PWR |
| 视频文件： | Linear Technology LT3652 |
| 设计资源： | DC1568A Design Files DC1568A Schematic |
| 特色产品： | Energy Harvesting Power Products |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LT3652 |
| 主要属性： | 多种化学，太阳能 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板 |
| 相关产品： | LT3652HVIMSE#TRPBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVIMSE#PBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVIDD#TRPBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVIDD#PBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEMSE#TRPBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVEDD#TRPBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEDD#PBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEMSE#PBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652IMSE#TRPBF-ND - IC BATT CHARGER SOLAR 2A 12MSOP LT3652IMSE#PBF-ND - IC BATT CHARGER SOLAR 2A 12MSOP 更多... |
LT3652
APPLICATIONS INFORMATION
full-charge float voltage. If a charge cycle is not successful
at EOC, the timer cycle resets and charging continues for
another full timer cycle.
When V BAT drops below 97.5% of the full-charge float
voltage, whether by battery loading or replacement of the
battery, the charger automatically reengages and starts
charging.
Preconditioning and Bad Battery Fault
A LT3652 has a precondition mode, where charge current
is limited to 15% of the programmed I CHG(MAX) , as set by
R SENSE . The precondition current corresponds to 15mV
across R SENSE .
Precondition mode is engaged while the voltage on the
V FB pin is below the precondition threshold (2.3V, or
0.7 ? V BAT(FLT) ). Once the V FB voltage rises above the
precondition threshold, normal full-current charging can
commence. The LT3652 incorporates 70mV of threshold
hysteresis to prevent mode glitching.
When the internal timer is used for termination, bad battery
detection is engaged. There is no provision for bad battery
detection if C/10 termination is used. A bad battery fault
is triggered when the voltage on V FB remains below the
precondition threshold for greater than 1/8 of a full timer
cycle (1/8 EOC). A bad battery fault is also triggered if a
normally charging battery re-enters precondition mode
after 1/8 EOC.
When a bad battery fault is triggered, the charging cycle
is suspended, so the CHRG status pin becomes high-
impedance. The FAULT pin is pulled low to signal a fault
detection.
Cycling the charger’s power or SHDN function initiates a
new charging cycle, but a LT3652 charger does not re-
quire a reset. Once a bad battery fault is detected, a new
timer charging cycle initiates when the V FB pin exceeds
the precondition threshold voltage. During a bad battery
fault, 0.5mA is sourced from the charger, so removing
the failed battery allows the charger output voltage to rise
and initiate a charge cycle reset. As such, removing a bad
battery resets the LT3652, so a new charge cycle is started
by connecting another battery to the charger output.
Battery Temperature Monitor and Fault
The LT3652 can accommodate battery temperature moni-
toring by using an NTC (negative temperature co-efficient)
thermistor close to the battery pack. The temperature
monitoring function is enabled by connecting a 10kΩ,
B = 3380 NTC thermistor from the NTC pin to ground. If the
NTC function is not desired, leave the pin unconnected.
The NTC pin sources 50μA, and monitors the voltage
dropped across the 10kΩ thermistor. When the voltage
on this pin is above 1.36V (0°C) or below 0.29V (40°C),
the battery temperature is out of range, and the LT3652
triggers an NTC fault. The NTC fault condition remains until
the voltage on the NTC pin corresponds to a temperature
within the 0°C to 40°C range. Both hot and cold thresholds
incorporate hysteresis that correspond to 5°C.
If higher operational charging temperatures are desired,
the temperature range can be expanded by adding series
resistance to the 10k NTC resistor. Adding a 0.91k resistor
will increase the effective hot temperature to 45°C.
During an NTC fault, charging is halted and both status
pins are pulled low. If timer termination is enabled, the
timer count is suspended and held until the fault condi-
tion is relieved.
Thermal Foldback
The LT3652 contains a thermal foldback protection feature
that reduces maximum charger output current if the IC
junction temperature approaches 125°C. In most cases,
on-chip temperatures servo such that any excessive tem-
perature conditions are relieved with only slight reductions
in maximum charger current.
3652fd
20
相关PDF资料 |
PDF描述 |
|---|---|
| GBB15DHHT | CONN EDGECARD 30POS .050 DIP SLD |
| GBM25DTBH-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| RT-375-1/16-X-SP-SM | HEAT SHRINK TUBING |
| RNF-100-3/8-GN-STK | HEAT SHRINK TUBING |
| GBM25DTBD-S189 | CONN EDGECARD 50POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1568A | 制造商:Linear Technology 功能描述:BATTERY CHARGER DEMO. BOARD ((NW)) |
| DC1571A-A | 功能描述:BOARD SAR ADC LTC2383-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571A-B | 功能描述:BOARD SAR ADC LTC2382-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571A-C | 功能描述:BOARD SAR ADC LTC2381-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571B | 制造商:Aleph America Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。