- 您现在的位置：买卖IC网 > PDF目录16760 > DC1568A (Linear Technology)BOARD BATTERY CHARGER SOLAR PWR PDF资料下载
参数资料
| 型号： | DC1568A |
| 厂商： | Linear Technology |
| 文件页数： | 7/26页 |
| 文件大小： | 0K |
| 描述： | BOARD BATTERY CHARGER SOLAR PWR |
| 视频文件： | Linear Technology LT3652 |
| 设计资源： | DC1568A Design Files DC1568A Schematic |
| 特色产品： | Energy Harvesting Power Products |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | LT3652 |
| 主要属性： | 多种化学，太阳能 |
| 次要属性： | LED 状态指示器 |
| 已供物品： | 板 |
| 相关产品： | LT3652HVIMSE#TRPBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVIMSE#PBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVIDD#TRPBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVIDD#PBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEMSE#TRPBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652HVEDD#TRPBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEDD#PBF-ND - IC BATTERY CHARGER 2A 12-DFN LT3652HVEMSE#PBF-ND - IC BATTERY CHARGER 2A 12-MSOP LT3652IMSE#TRPBF-ND - IC BATT CHARGER SOLAR 2A 12MSOP LT3652IMSE#PBF-ND - IC BATT CHARGER SOLAR 2A 12MSOP 更多... |
LT3652
PIN FUNCTIONS
V IN (Pin 1): Charger Input Supply. V IN operating range
is 4.95V to 32V. V IN must be 3.3V greater than the pro-
grammed output battery ?oat voltage (V BAT(FLT) ) for reli-
able start-up. (V IN – V BAT(FLT) ) ≥ 0.75V is the minimum
operating voltage, provided (V BOOST – V SW ) ≥ 2V. I VIN ~
85μA after charge termination.
V IN_REG (Pin 2): Input Voltage Regulation Reference.
Maximum charge current is reduced when this pin is below
2.7V. Connecting a resistor divider from V IN to this pin
enables programming of minimum operational V IN voltage.
This is typically used to program the peak power voltage
for a solar panel. The LT3652 servos the maximum charge
current required to maintain the programmed operational
V IN voltage, through maintaining the voltage on V IN_REG
at or above 2.7V. If the voltage regulation feature is not
used, connect the pin to V IN .
SHDN (Pin 3): Precision Threshold Shutdown Pin. The
enable threshold is 1.2V (rising), with 120mV of input
hysteresis. When in shutdown mode, all charging functions
are disabled. The precision threshold allows use of the
SHDN pin to incorporate UVLO functions. If the SHDN pin
is pulled below 0.4V, the IC enters a low current shutdown
mode where V IN current is reduced to 15μA. Typical SHDN
pin input bias current is 10nA. If the shutdown function
is not desired, connect the pin to V IN .
CHRG (Pin 4): Open-Collector Charger Status Output;
typically pulled up through a resistor to a reference volt-
age. This status pin can be pulled up to voltages as high
as V IN when disabled, and can sink currents up to 10mA
when enabled. During a battery charging cycle, if required
charge current is greater than 1/10 of the programmed
maximum current (C/10), CHRG is pulled low. A tem-
perature fault also causes this pin to be pulled low. After
C/10 charge termination or, if the internal timer is used
for termination and charge current is less than C/10, the
CHRG pin remains high-impedance.
FAULT (Pin 5): Open-Collector Charger Status Output;
typically pulled up through a resistor to a reference volt-
age. This status pin can be pulled up to voltages as high
as V IN when disabled, and can sink currents up to 10mA
when enabled. This pin indicates fault conditions during a
battery charging cycle. A temperature fault causes this pin
to be pulled low. If the internal timer is used for termina-
tion, a bad battery fault also causes this pin to be pulled
low. If no fault conditions exist, the FAULT pin remains
high-impedance.
TIMER (Pin 6): End-Of-Cycle Timer Programming Pin.
If a timer-based charge termination is desired, connect
a capacitor from this pin to ground. Full charge end-of-
cycle time (in hours) is programmed with this capacitor
following the equation:
t EOC = C TIMER ? 4.4 ? 10 6
A bad battery fault is generated if the battery does not
achieve the precondition threshold voltage within one-
eighth of t EOC , or:
t PRE = C TIMER ? 5.5 ? 10 5
A 0.68μF capacitor is typically used, which generates a
timer EOC at three hours, and a precondition limit time of
22.5 minutes. If a timer-based termination is not desired,
the timer function is disabled by connecting the TIMER
pin to ground. With the timer function disabled, charging
terminates when the charge current drops below a C/10
threshold, or I CHG(MAX) /10
V FB (Pin 7): Battery Float Voltage Feedback Reference. The
charge function operates to achieve a ?nal ?oat voltage of
3.3V on this pin. Output battery ?oat voltage (V BAT(FLT) )
is programmed using a resistor divider. V BAT(FLT) can be
programmed up to 14.4V.
The auto-restart feature initiates a new charging cycle
when the voltage at the V FB pin falls 2.5% below the ?oat
voltage reference.
The V FB pin input bias current is 110nA. Using a resistor
divider with an equivalent input resistance at the V FB pin
of 250k compensates for input bias current error.
Required resistor values to program desired V BAT(FLT)
follow the equations:
R1 = (V BAT(FLT) ? 2.5 ? 10 5 )/3.3 (Ω)
R2 = (R1 ? 2.5 ? 10 5 )/(R1 - (2.5 ? 10 5 )) (Ω)
R1 is connected from BAT to V FB , and R2 is connected
from V FB to ground.
3652fd
7
相关PDF资料 |
PDF描述 |
|---|---|
| GBB15DHHT | CONN EDGECARD 30POS .050 DIP SLD |
| GBM25DTBH-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| RT-375-1/16-X-SP-SM | HEAT SHRINK TUBING |
| RNF-100-3/8-GN-STK | HEAT SHRINK TUBING |
| GBM25DTBD-S189 | CONN EDGECARD 50POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1568A | 制造商:Linear Technology 功能描述:BATTERY CHARGER DEMO. BOARD ((NW)) |
| DC1571A-A | 功能描述:BOARD SAR ADC LTC2383-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571A-B | 功能描述:BOARD SAR ADC LTC2382-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571A-C | 功能描述:BOARD SAR ADC LTC2381-16 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:QuikEval™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| DC1571B | 制造商:Aleph America Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。