- 您现在的位置：买卖IC网 > PDF目录19026 > DC1620A-H (Linear Technology)BOARD DEMO 105MSPS LTC2144-14 PDF资料下载
参数资料
| 型号： | DC1620A-H |
| 厂商： | Linear Technology |
| 文件页数： | 20/38页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 105MSPS LTC2144-14 |
| 软件下载： | QuikEval II System |
| 设计资源： | DC1620A Design Files DC1620A Schematic |
| 标准包装： | 1 |
| 系列： | * |
| 相关产品： | DC890B-ND - BOARD USB DATA COLLECTION |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
27
21454314fa
LTC2145-14/
LTC2144-14/LTC2143-14
allowed so the on-chip references can settle from the slight
temperature shift caused by the change in supply current
as the A/D leaves nap mode. Either channel 2 or both chan-
nels can be placed in nap mode; it is not possible to have
channel 1 in nap mode and channel 2 operating normally.
Sleep mode and nap mode are enabled by mode control
register A1 (serial programming mode), or by SDI and
SDO (parallel programming mode).
DEVICE PROGRAMMING MODES
The operating modes of the LTC2145-14/LTC2144-14/
LTC2143-14 can be programmed by either a parallel in-
terface or a simple serial interface. The serial interface has
more flexibility and can program all available modes. The
parallel interface is more limited and can only program
some of the more commonly used modes.
Parallel Programming Mode
To use the parallel programming mode, PAR/SER should
be tied to VDD. The CS, SCK, SDI and SDO pins are binary
logic inputs that set certain operating modes. These pins
can be tied to VDD or ground, or driven by 1.8V, 2.5V, or
3.3V CMOS logic. When used as an input, SDO should
be driven through a 1k series resistor. Table 2 shows the
modes set by CS, SCK, SDI and SDO.
Table 2. Parallel Programming Mode Control Bits (PAR/SER = VDD)
PIN
DESCRIPTION
CS
Clock Duty Cycle Stabilizer Control Bit
0 = Clock Duty Cycle Stabilizer Off
1 = Clock Duty Cycle Stabilizer On
SCK
Digital Output Mode Control Bit
0 = Full Rate CMOS Output Mode
1 = Double Data Rate LVDS Output Mode
(3.5mA LVDS Current, Internal Termination Off)
SDI/SDO Power Down Control Bit
00 = Normal Operation
01 = Channel 1 in Normal Operation, Channel 2 in Nap Mode
10 = Channel 1 and Channel 2 in Nap Mode
11 = Sleep Mode (Entire Device Powered Down)
APPLICATIONS INFORMATION
Digital Output Test Patterns
To allow in-circuit testing of the digital interface to the
A/D, there are several test modes that force the A/D data
outputs (OF, D13-D0) to known values:
All 1s: All outputs are 1
All 0s: All outputs are 0
Alternating: Outputs change from all 1s to all 0s on
alternating samples.
Checkerboard: Outputs change from
101010101010101 to 010101010101010 on alternat-
ing samples.
The digital output test patterns are enabled by serially
programming mode control register A4. When enabled,
the Test Patterns override all other formatting modes: 2’s
complement, randomizer, alternate bit polarity.
Output Disable
The digital outputs may be disabled by serially program-
ming mode control register A3. All digital outputs including
OF and CLKOUT are disabled. The high-impedance disabled
state is intended for in-circuit testing or long periods of
inactivity – it is too slow to multiplex a data bus between
multiple converters at full speed. When the outputs are
disabled both channels should be put into either sleep or
nap mode.
Sleep and Nap Modes
The A/D may be placed in sleep or nap modes to conserve
power. In sleep mode the entire device is powered down,
resulting in 1mW power consumption. The amount of time
required to recover from sleep mode depends on the size
of the bypass capacitors on VREF, REFH, and REFL. For the
suggested values in Fig. 8, the A/D will stabilize after 2ms.
In nap mode the A/D core is powered down while the internal
reference circuits stay active, allowing faster wakeup than
from sleep mode. Recovering from nap mode requires at
least 100 clock cycles. If the application demands very
accurate DC settling then an additional 50μs should be
相关PDF资料 |
PDF描述 |
|---|---|
| 1691 | LAMP INCAND S-8 BAYONET 28V |
| KC2520B24.0000C10E00 | OSCILLATOR 24.0000MHZ SMD |
| DC919A-F | BOARD DEMO 16BIT MSPS LTC2202 |
| 1309 | LAMP INCAND B6 SGL BAYONET 28V |
| 1683 | LAMP INCAND S-8 BAYONET 28V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1620A-I | 功能描述:BOARD DEMO 80MSPS LTC2143-14 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1620A-J | 功能描述:BOARD DEMO 65MSPS LTC2142-14 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1620A-K | 功能描述:BOARD DEMO 40MSPS LTC2141-14 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1620A-L | 功能描述:BOARD DEMO 25MSPS LTC2140-14 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1620A-M | 功能描述:BOARD DEMO 125MSPS LTC2145-12 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
发布紧急采购，3分钟左右您将得到回复。