- 您现在的位置：买卖IC网 > PDF目录20407 > DC1623A (Linear Technology)BOARD EVAL LTM8003 PDF资料下载
参数资料
| 型号： | DC1623A |
| 厂商： | Linear Technology |
| 文件页数： | 17/26页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL LTM8003 |
| 软件下载： | LTM8033 Spice Model |
| 设计资源： | DC1623A Design Files |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 3A |
| 输入电压： | 5.5 ~ 36 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 425kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM8033 |
LTM8033
APPLICATIONS INFORMATION
Hot-Plugging Safely
The small size, robustness and low impedance of ceramic
capacitors make them an attractive option for the input
bypass capacitor of LTM8033. However, these capacitors
can cause problems if the LTM8033 is plugged into a live
supply (see Application Note 88 for a complete discus-
sion). The low loss ceramic capacitor combined with
stray inductance in series with the power source forms an
underdamped tank circuit, and the voltage at the V IN pin
of the LTM8033 can ring to more than twice the nominal
input voltage, possibly exceeding the LTM8033’s rating and
damaging the part. A similar phenomenon can occur inside
the LTM8032 module, at the output of the integrated EMI
filter (FIN), with the same potential of damaging the part.
If the input supply is poorly controlled or the user will be
plugging the LTM8033 into an energized supply, the input
network should be designed to prevent this overshoot.
This can be accomplished by installing a small resistor
in series to V IN , but the most popular method of control-
ling input voltage overshoot is adding an electrolytic bulk
capacitor to the V IN or FIN net. This capacitor’s relatively
high equivalent series resistance damps the circuit and
eliminates the voltage overshoot. The extra capacitor
improves low frequency ripple filtering and can slightly
improve the efficiency of the circuit, though it can be a
large component in the circuit.
Electromagnetic Compliance
The LTM8033 was evaluated by an independent nation-
ally recognized test lab and found to be compliant with
EN 55022 class B: 2006 by a wide margin. Sample graphs
of the LTM8033’s radiated EMC performance are given in the
Typical Performance Characteristics section, while further
data, operating conditions and test set-up are detailed in
the electromagnetic compatibility test report, available
on the Linear Technology website. Conducted emissions
requirements may be met by adding an appropriate input
power line filter. The proper implementation of this filter
depends upon the system operating and performance
conditions as a whole, of which the LTM8033 is typically
only a component, so conducted emissions are not ad-
dressed at this level.
Thermal Considerations
The LTM8033 output current may need to be derated if it
is required to operate in a high ambient temperature or
deliver a large amount of continuous power. The amount
of current derating is dependent upon the input voltage,
output power and ambient temperature. The temperature
rise curves given in the Typical Performance Charac-
teristics section can be used as a guide. These curves
were generated by an LTM8033 mounted to a 40cm 2
4-layer FR4 printed circuit board. Boards of other sizes
and layer count can exhibit different thermal behavior, so
it is incumbent upon the user to verify proper operation
over the intended system’s line, load and environmental
operating conditions.
The thermal resistance numbers listed in the Pin Con-
figuration are based on modeling the μModule package
mounted on a test board specified per JESD51-9 “Test
Boards for Area Array Surface Mount Package Thermal
Measurements.” The thermal coefficients provided in this
page are based on JESD 51-12 “Guidelines for Reporting
and Using Electronic Package Thermal Information.”
For increased accuracy and fidelity to the actual application,
many designers use FEA to predict thermal performance.
To that end, the Pin Configuration typically gives four
thermal coefficients:
? θ JA – Thermal resistance from junction to ambient.
? θ JCBOTTOM – Thermal resistance from junction to the
bottom of the product case.
? θ JCTOP – Thermal resistance from junction to top of
the product case.
? θ JB – Thermal resistance from junction to the printed
circuit board.
8033fa
For more information www.linear.com/LTM8033
17
相关PDF资料 |
PDF描述 |
|---|---|
| 346-080-520-802 | CONNECTOR CARDEDGE 80POS .125 |
| CS8312YDR8 | IC PREDRIVER IGBT IGNITION 8SOIC |
| 346-080-520-202 | CARD EDGE CONN 80POS .125 X .250 |
| MKP1V120RL | SIDAC BIDIR 0.9A 120V DO41 |
| RCM12DCMD | CONN EDGECARD 24POS .156 WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1625A-A | 功能描述:BOARD DEMO FOR LTC4227-1 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1625A-B | 功能描述:BOARD DEMO FOR LTC4227-2 RoHS:是 类别:未定义的类别 >> 其它 系列:* 标准包装:1 系列:* 其它名称:MS305720A |
| DC1627 | 制造商:INTRONICS 制造商全称:INTRONICS 功能描述:15 Watt Triple Output DC-DC Converters |
| DC1627A-A | 制造商:Linear Technology 功能描述:EVAL BOARD FOR LTC4226-1 制造商:Linear Technology 功能描述:DEMO BOARD, LTC4226 HOT SWAP CONTROLLER, Silicon Manufacturer:Linear Technology, Silicon Core Number:LTC4226CUD-1, Kit Application Type:Power Management, Application Sub Type:Hot Swap Controller, Kit Contents:Demo Board LTC4226CUD-1 , RoHS Compliant: NA |
| DC1627A-B | 制造商:Linear Technology 功能描述:EVAL BOARD FOR LTC4226-2 制造商:Linear Technology 功能描述:DEMO BOARD, LTC4226 HOT SWAP CONTROLLER, Silicon Manufacturer:Linear Technology, Silicon Core Number:LTC4226CUD-2, Kit Application Type:Power Management, Application Sub Type:Hot Swap Controller, Kit Contents:Demo Board LTC4226CUD-2 , RoHS Compliant: NA |
发布紧急采购，3分钟左右您将得到回复。