- 您现在的位置：买卖IC网 > PDF目录20407 > DC1743A (Linear Technology)BOARD DEMO LTM4613 PDF资料下载
参数资料
| 型号： | DC1743A |
| 厂商： | Linear Technology |
| 文件页数： | 12/28页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO LTM4613 |
| 产品培训模块： | µModule® Family of EN55022 Class B Certified Regulators |
| 设计资源： | DC1743A Design Files |
| 标准包装： | 1 |
| 系列： | µModule® |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V，5V，12V |
| 电流 - 输出： | 8A |
| 输入电压： | 5 ~ 36 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 165kHz，250kHz，600kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTM4613 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTM4613
APPLICATIONS INFORMATION
V OUT
? 3 ? R fSET ? 133k ?
? R fSET ? 2 ? 133k ? ?
D = OUT
? D ? ( 1 – D )
I CIN(RMS) =
Foroutputvoltagesmorethan12V,thefrequencycanbe
higher than 600kHz, thus reducing the efficiency signifi-
cantly. Additionally, the minimum off time 400ns normally
limits the operation when the input voltage is close to the
output voltage. Therefore, it is recommended to lower the
frequency in these conditions by connecting a resistor
(R fSET ) from the f SET pin to V IN , as shown in Figure 20.
f =
5 ? 10 ? 11 ?
The load current can affect the frequency due to its con-
stant on-time control. If constant frequency is a necessity,
the PLLIN pin can be used to synchronize the frequency
of the LTM4613 to an external clock subject to minimum
on-time and off-time limits, as shown in Figures 21 to 23.
Input Capacitors
LTM4613 is designed to achieve the low input conducted
EMI noise due to the fast switching of turn-on and turn-
off. Additionally, a high-frequency inductor is integrated
into the input line for noise attenuation. V D and V IN pins
are available for external input capacitors to form a high
frequency π filter. As shown in Figure 18, the ceramic
capacitors, C1-C3, on the V D pins is used to handle most
of the RMS current into the converter, so careful attention
is needed for capacitors C1-C3 selection.
For a buck converter, the switching duty cycle can be
estimated as:
V
V IN
Withoutconsideringtheinductorcurrentripple,theRMS
current of the input capacitor can be estimated as:
I OUT(MAX)
η
In this equation, η is the estimated efficiency of the
power module. Note the capacitor ripple current ratings
are often based on temperature and hours of life. This
makes it advisable to properly derate the input capacitor,
or choose a capacitor rated at a higher temperature than
required. Always contact the capacitor manufacturer for
derating requirements.
In a typical 8A output application, three very low ESR,
X5R or X7R, 10μF ceramic capacitors are recommended
for C1-C3. This decoupling capacitance should be placed
directly adjacent to the module V D pins in the PCB layout
to minimize the trace inductance and high frequency AC
noise. Each 10μF ceramic is typically good for 2A of RMS
ripple current. Refer to your ceramics capacitor catalog
for the RMS current ratings.
To attenuate the high frequency noise, extra input capacitors
should be connected to the V IN pads and placed before the
high frequency inductor to form the π filter. One of these
low ESR ceramic input capacitors is recommended to be
close to the connection into the system board. A large bulk
100μF capacitor is only needed if the input source imped-
ance is compromised by long inductive leads or traces.
Output Capacitors
The LTM4613 is designed for low output voltage ripple.
The bulk output capacitors defined as C OUT are chosen
with low enough effective series resistance (ESR) to meet
the output voltage ripple and transient requirements. C OUT
can be low ESR tantalum capacitor, low ESR polymer ca-
pacitor or ceramic capacitor. The typical capacitance is 4 ×
47μF if all ceramic output capacitors are used. Additional
output filtering may be required by the system designer,
if further reduction of output ripple or dynamic transient
spike is required. Table 2 shows a matrix of different output
voltages and output capacitors to minimize the voltage
droop and overshoot during a 4A load transient. The table
optimizes total equivalent ESR and total bulk capacitance
to maximize transient performance.
Multiphase operation with multiple LTM4613 devices in
parallel will also lower the effective output ripple current
due to the phase interleaving operation. Refer to Figure 4
for the normalized output ripple current versus the duty
cycle. Figure 4 provides a ratio of peak-to-peak output
ripple current to the inductor ripple current as functions
of duty cycle and the number of paralleled phases. Pick
the corresponding duty cycle and the number of phases
to get the correct output ripple current value. For example,
each phase’s inductor ripple current ? I L is ~5.0A for a 36V
4613f
12
相关PDF资料 |
PDF描述 |
|---|---|
| RLB0712-151KL | INDUCTOR 150UH 10% RADIAL |
| 346-080-521-201 | CARDEDGE 80POS DUAL .125 GREEN |
| RCM12DCMN | CONN EDGECARD 24POS .156 WW |
| BAS16TW-7 | DIODE SW ARRAY 75V 200MW SC70-6 |
| MKP1V130RL | SIDAC BIDIR 0.9A 130V DO-41 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC1746A-A | 功能描述:EVALUATION KIT LOW EMI LTM2881-3 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:µModule® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| DC1746A-B | 功能描述:EVALUATION KIT LOW EMI LTM2881-5 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:µModule® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| DC1747A-A | 功能描述:EVALUATION LOW EM1 KIT LTM2882-3 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:µModule® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| DC1747A-B | 功能描述:EVALUATION KIT LOW EM1 LTM2882-5 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:µModule® 标准包装:1 系列:- 主要目的:数字电位器 嵌入式:- 已用 IC / 零件:AD5258 主要属性:- 次要属性:- 已供物品:板 相关产品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| DC1748A-A | 制造商:Linear Technology 功能描述:BOARD EVAL FOR LTM2883 |
发布紧急采购，3分钟左右您将得到回复。