- 您现在的位置：买卖IC网 > PDF目录17103 > DC752A-B (Linear Technology)BOARD DAC LTC2704-16 PDF资料下载
参数资料
| 型号： | DC752A-B |
| 厂商： | Linear Technology |
| 文件页数： | 9/22页 |
| 文件大小： | 0K |
| 描述： | BOARD DAC LTC2704-16 |
| 软件下载： | QuikEval System |
| 设计资源： | DC752A Design File DC752A Schematic |
| 标准包装： | 1 |
| 系列： | QuikEval™, SoftSpan™ |
| DAC 的数量： | 4 |
| 位数： | 16 |
| 数据接口： | 串行，SPI? |
| 设置时间： | 10µs |
| DAC 型： | 电压 |
| 已供物品： | 板 |
| 已用 IC / 零件： | LTC2704-16 |
| 相关产品： | DC590B-ND - BOARD DEMO USB SERIAL CONTROLLER LTC2704IGW-16#TRPBF-ND - IC DAC 16BIT QUAD VOUT 44-SSOP LTC2704IGW-16#PBF-ND - IC DAC 16BIT QUAD VOUT 44-SSOP LTC2704CGW-16#TRPBF-ND - IC DAC 16BIT QUAD VOUT 44-SSOP LTC2704CGW-16#PBF-ND - IC DAC 16BIT QUAD VOUT 44-SSOP |
LTC2704
17
2704fd
APPLICATIONS INFORMATION
Overview
The LTC2704 is a highly integrated device, greatly sim-
plifying design and layout as compared to a design using
multiple current output DACs and separate ampliers. A
similar design using four separate current output DACs
would require six precision op amps, compensation capaci-
tors, bypass capacitors for each amplier, several times as
much PCB area and a more complicated serial interface.
Still, it is important to avoid some common mistakes in
order to achieve full performance. DC752A is the evalu-
ation board for the LTC2704. It is designed to meet all
data sheet specications, and to allow the LTC2704 to be
integrated into other prototype circuitry. All force/sense
lines are available to allow the addition of current booster
stages or other output circuits.
The DC752A design is presented as a tutorial on properly
applying the LTC2704. This board shows how to properly
return digital and analog ground currents, and how to
compensate for small differences in ground potential
between the two banks of two DACs. There are other ways
to ground the LTC2704, but the one requirement is that
analog and digital grounds be connected at the LTC2704
by a very low impedance path. It is NOT advisable to split
the ground planes and connect them with a jumper or
inductor. When in doubt, use a single solid ground plane
rather than separate planes.
The LTC2704 does allow the ground potential of the DACs
to vary by ±300mV with respect to analog ground, allowing
compensation for ground return resistance.
Power Supply Grounding and Noise
LTC2704 V+ and V– pins are the supplies to all of the
output ampliers, ground sense ampliers and reference
inversion ampliers. These ampliers have good power
supply rejection, but the V+ and V– supplies must be free
from wideband noise. The best scheme is to prelter low
noise regulators such as the LT1761 (positive) and LT1964
(negative). Refer to Linear Technology Application Note
101, Minimizing Switching Regulator Residue in Linear
Regulator Outputs.
The LTC2704 VDD pin is the supply for the digital logic
and analog DAC switches and is very sensitive to noise. It
must be treated as an analog supply. The evaluation board
uses an LT1790 precision reference as the VDD supply to
minimize noise.
The GND pin is the return for digital currents and the
AGND pin is a bias point for internal analog circuitry. Both
of these pins must be tied to the same point on a quiet
ground plane.
Each DAC has a separate ground sense pin that can be used
to compensate for small differences in ground potential
within a system. Since DACs A and B are associated with
REF1 and DACs C and D are associated with REF2, the
grounds must be grouped together as follows:
AGNDA, AGNDB and REFG1 tied together (“GND1” on
DC752A)
AGNDC, AGNDD and REFG2 tied together (“GND2” on
DC752A)
This scheme allows compensation for ground return IR
drops, as long as the resistance is shared by both DACs
in a group. This implies that the ground return for DACs
A and B must be as close as possible, and GND1 must
be connected to this point through a low current, low
resistance trace. (Similar for DACs C and D.)
Figure 3 shows the top layer of the evaluation board. The
GND1 trace connects REFG1, AGNDA, AGNDB and the
ground pin of the LT1236 precision reference (U4.) This
point is the ground reference for DACs A and B. The GND2
trace connects REFG2, AGNDC, AGNDD and the ground pin
of the other LT1236 precision reference (U5). This point
is the ground reference for DACs C and D.
Voltage Reference
A high quality, low noise reference such as the LT1236
or LT1027 must be used to achieve full performance.
The ground terminal of this reference must be connected
directly to the common ground point. If GND1 and GND2
are separate, then two references must be used.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9785-DPG2-EBZ | BOARD EVALUATION FOR AD9785 |
| EEM36DTMD-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| EEM36DTMH-S189 | CONN EDGECARD 72POS R/A .156 SLD |
| 0210390421 | CABLE FLAT FLEX 1.18" 1MM 26POS |
| EVAL-AD5791SDZ | BOARD EVAL FOR AD5791 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC756A | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4150CMS 制造商:Linear Technology 功能描述:EVAL BOARD, LTC4150CMS BATTERY MONITOR |
| DC756KA-GB | 制造商:DEWALT 功能描述:DRILL 12V CHARGER W.UK-PLUG |
| DC757A-A | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4302CMS-1 |
| DC757A-B | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4302CMS-2 |
| DC757KA-GB | 制造商:DEWALT 功能描述:DRILL 14.4V |
发布紧急采购，3分钟左右您将得到回复。