- 您现在的位置：买卖IC网 > PDF目录17070 > DC798B (Linear Technology)BOARD DELTA SIGMA ADC LTC2480 PDF资料下载
参数资料
| 型号： | DC798B |
| 厂商： | Linear Technology |
| 文件页数： | 13/42页 |
| 文件大小： | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2480 |
| 软件下载： | QuikEval System |
| 设计资源： | DC798B Design File DC798B Schematic |
| 标准包装： | 1 |
| 系列： | QuikEval™ |
| ADC 的数量： | 1 |
| 位数： | 16 |
| 采样率（每秒）： | 7.5 |
| 数据接口： | MICROWIRE?，串行，SPI? |
| 已用 IC / 零件： | LTC2480 |
| 已供物品： | 板 |
| 相关产品： | LTC2480HMS#TRPBF-ND - IC ADC DELTA SIGMA 16BIT 10MSOP LTC2480HDD#TRPBF-ND - IC ADC DELTA SIGMA 16BIT 10DFN LTC2480HDD#PBF-ND - IC ADC 16BIT SRL 7.5SPS 10DFN LTC2480HMS#PBF-ND - IC ADC 16BIT SER/SPI 10MSOP LTC2480IMS#TRPBF-ND - IC ADC 16BIT 10-MSOP LTC2480IMS#PBF-ND - IC ADC 16BIT 10-MSOP LTC2480IDD#TRPBF-ND - IC ADC 16BIT 10-DFN LTC2480CMS#TRPBF-ND - IC ADC 16BIT 10-MSOP LTC2480CMS#PBF-ND - IC ADC 16BIT 10-MSOP LTC2480CDD#TRPBF-ND - IC ADC 16BIT 10-DFN 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LTC2480
0
2480fd
value with a temperature coefficient of 420/(27 + 273) =
1.40mV/°C (SLOPE), as shown in Figure 4. The internal
PTAT signal is used in a single-ended mode referenced
to device ground internally. The GAIN is automatically
set to one (independent of the values of GS0, GS1, GS2)
in order to preserve the PTAT property at the ADC output
code and avoid an out of range error. The 1x speed mode
with automatic offset calibration is automatically selected
for the internal PTAT signal measurement as well.
If the same VREF source is used during calibration and
temperature measurement, the actual value of the VREF
is not needed to measure the temperature as shown in
the calculation below:
T
R
V
SLOPE
R
T
C
SDO
REF
SDO
=
+
(
)
–
–
273
0
0 273 273
Reference Voltage Range
The LTC2480 external reference voltage range is 0.1V
to VCC. The converter output noise is determined by
the thermal noise of the front-end circuits, and as such,
its value in nanovolts is nearly constant with reference
voltage. Since the transition noise (600nV) is much less
than the quantization noise (VREF/217), a decrease in the
reference voltage will increase the converter resolution. A
reduced reference voltage will also improve the converter
performance when operated with an external conversion
clock (external fO signal) at substantially higher output
data rates (see the Output Data Rate section). VREF must
be ≥1.1V to use the internal temperature sensor.
The negative reference input to the converter is internally
tied to GND. GND (Pin 8) should be connected to a ground
plane through as short a trace as possible to minimize
voltage drop. The LTC2480 has an average operational
current of 160A and for 0.1Ω parasitic resistance, the
voltage drop of 16V causes a gain error of 3.2ppm for
VREF = 5V.
Input Voltage Range
The analog input is truly differential with an absolute/com-
mon mode range for the IN+ and IN– input pins extending
from GND – 0.3V to VCC + 0.3V. Outside these limits, the
ESD protection devices begin to turn on and the errors
due to input leakage current increase rapidly. Within these
limits, the LTC2480 converts the bipolar differential input
signal, VIN = IN+ – IN–, from –FS to +FS where FS = 0.5
VREF/GAIN. Outside this range, the converter indicates the
overrangeortheunderrangeconditionusingdistinctoutput
codes.Sincethedifferentialinputcurrentcancellationdoes
not rely on an on-chip buffer, current cancellation as well
as DC performance is maintained rail-to-rail.
applicaTions inForMaTion
TEMPERATURE (°C)
–60
V PTAT
(mV)
500
600
120
2480 F04
400
200
30
0
90
–30
60
300
VCC = 5V
IM = 1
FO = GND
SLOPE = 1.40mV/°C
Figure 4. Internal PTAT Signal vs Temperature
When using the internal temperature sensor, if the output
code is normalized to RSDO = VPTAT/VREF, the temperature
is calculated using the following formula:
T
R
V
SLOPE
T
R
V
SLOPE
K
SDO
REF
C
SDO
REF
=
°
–
in Kelvin
and
in C
273
where SLOPE is nominally 1.4mV/°C.
Since the PTAT signal can have an initial value variation
which results in errors in SLOPE, to achieve better tem-
perature measurements, a one-time calibration is needed
to adjust the SLOPE value. The converter output of the
PTAT signal, R0SDO, is measured at a known temperature
T0 (in °C) and the SLOPE is calculated as:
SLOPE
R
V
T
SDO
REF
=
+
0
0 273
This calibrated SLOPE can be used to calculate the tem-
perature.
相关PDF资料 |
PDF描述 |
|---|---|
| EVAL-AD7841EBZ | BOARD EVAL FOR AD7841 |
| XRP2525ID-2-F | IC PWR SW USB 3.0 SINGLE NSOIC8 |
| EVAL-AD7839EBZ | BOARD EVAL FOR AD7839 |
| NRS6010T4R7MMGF | INDUCTOR POWER 4.7UH 1.4A SMD |
| AD7940-DBRD | BOARD EVAL FOR AD7940 STAMP SPI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DC-7G3EWA | 制造商:Kingbright Corporation 功能描述:Red/Green 10-seg LED lightbar, DC-7G3EWA |
| DC7G3HWA | 功能描述:LED条和阵列 7GR 3RED BARGRAFT 10 SEGMENT RoHS:否 制造商:Avago Technologies 产品:LED Light Bars 照明颜色:Red 光强度:45 mcd 封装:Tube |
| DC-7G3HWA | 制造商:Kingbright Corporation 功能描述: |
| DC7K67J/4LR61 | 制造商:Duracell 功能描述: |
| DC8 | 制造商:Cliff Electronic Components 功能描述:SOCKET PCB DC POWER 1.3MM PK10 制造商:Cliff Electronic Components 功能描述:SOCKET, PCB, DC POWER, 1.3MM, PK10 制造商:Cliff Electronic Components 功能描述:SOCKET, PCB, DC POWER, 1.3MM, PK10, Series:DC, Gender:Receptacle, Voltage Rating |
发布紧急采购，3分钟左右您将得到回复。