ANALOG OUTPUT GAIN CONTROL AND PHASING
The DS-11802 is pin-programmable for gains of 0.5, 1.0 and 2.0.
TABLE 2 details the programming of gain control pins 23 (GC1)
and 24 (GC2). When both pins are left unconnected or open, the
gain of the converter is 2.0. The output signal would be: 2 Vin
sin
θ and 2 Vin cosθ. When GC2 is connected to GND and GC1
is left open, the converter gain is 1.0. When GC1 is connected
to GND and GC2 is left open, the converter gain is 0.5. When
looking at the equivalent gain circuit (see FIGURE 2) the gain of
the converter can be modified by adding a resistor between GC1
or GC2 and GND.
2
8 MSBs enter high
byte input register.
High byte register
remains unaffected.
8 LSBs enter low byte
input register.
Low byte register
remains unaffected.
Data from input regis-
ters transferred to
holding register.
Data in holding regis-
ter remains unaffected.
Logic 1
Logic 0
Logic 1
Logic 0
Logic 1
Logic 0
REGISTER CONTROLS
HBE
(High Byte Enable)
LBE
(Low Byte Enable)
LDC
(Load Converter)
No external logic volt-
ages required.
CMOS transient pro-
tected.
For less than 16 bits,
unused pins can be
left unconnected.
Pins not used can be
left unconnected.
DIGITAL INPUTS
Logic Voltage Levels
Logic 0
Logic 1
Loading
Input Current
Data Bits (B1-B16)
HBE, LBE, LDC
ANALOG OUTPUTS
SIN
θ
COS
θ
Converter Gain (K)
Radius Accuracy
Output Current
Output Impedance
Zero Offset (dc)
Offset Drift
Output Settling Time
Op amp buffer
0 to ±10 Vp ac or dc
dc to 1000 Hz
1 M
min
ANALOG INPUT
(VIN)
Voltage
Frequency Range
Input Resistance
16 Bits
±4 arc-minutes
±2 arc-minutes
±1 arc-minutes
DIGITAL ANGULAR
Resolution
Accuracy
REMARKS
VALUE
PARAMETER
TABLE 1. DS-11802 SPECIFICATIONS
For ±10 V pk output.
±15 V dc ±10%
±25 mA max
80 db typ
POWER SUPPLIES
Supply Voltages (±Vs)
Supply Current
Supply Rejection
Before data transfer.
Before input data
changes.
200
ηsec min
200
ηsec min
REGISTER CONTROLS
(Continued)
Data Set-up Time
Data Hold Time
ABSOLUTE MAXIMUM RATINGS
Reference Input:
-Vs to +Vs
Power Supply Voltage (±Vs):
±18 V dc
Digital Inputs:
-0.3 V dc to +6.5 V dc
PHYSICAL
CHARACTERISTICS
Type
Size
Weight
REMARKS
VALUE
PARAMETER
TABLE 1. DS-11802 SPECIFICATIONS (CONTINUED)
Bit 1 = MSB, Bit 16 = LSB
Accuracy applies over
operating temperature
range.
K Vin SIN
θ
K Vin COS
θ
0.5 ±0.2%
1.0 ±0.2%
2.0 ±0.2%
±0.1%
2 mA rms
< 1 ohm
±10 mV typical
±25 mV max
25
V/°C
30
sec max to
accuracy of con-
verter
±10 Vp AC or DC
Pin 23 connected to gnd.
Pin 24 no connection.
Pin 24 connected to gnd.
Pin 23 no connection.
Pin 23 and 24 floating.
Guaranteed, but not
tested.
Op amp output.
For any digital step
change.
28 Pin Double DIP
0.6 x 1.4 x 0.2 in.
(15 x 36 x 5) mm
0.5 oz
(15 gm) max
GC1
(PIN 23)
GC2
(PIN 24)
GAIN
(K)
Open
2.0
Gnd
Open
0.5
Open
Gnd
1.0
TABLE 2. GAIN CONTROL PINS
0°C to +70°C
-40°C to +85°C
-55°C to +125°C
-65°C to +135°C
-0.3 V DC to 0.8 V DC
2.4 V DC to 5.5 V DC
0.1 TTL load
15
A typ, “active”
pull-down to gnd
-15
A typ, “active”
pull-up to internal
logic supply
TEMPEATURE RANGES
Operating Case
-3XX and -8XX
-5XX and -2XX
-1XX and -4XX
Storage
Users are cautioned against using a large value resistor to
modify the gain, as the temperature coefficient of the exter-
nal resistor will not be matched with the TCR of the internal
resistor. The internal gain resistors have an accuracy of 0.05%.
FIGURE 3 illustrates the output phasing between the reference
voltage Vin and the analog output signals as a function of the
digital angle and the converter gain K (0.5, 1.0, or 2.0).