- 您现在的位置：买卖IC网 > PDF目录1912 > DS100BR111SQE/NOPB (National Semiconductor)IC REPEATER 10.3GBPS 2CH 24LLP PDF资料下载
参数资料
| 型号： | DS100BR111SQE/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 10/43页 |
| 文件大小： | 0K |
| 描述： | IC REPEATER 10.3GBPS 2CH 24LLP |
| 标准包装： | 250 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
SNLS338E – JANUARY 2011 – REVISED FEBRUARY 2013
EEPROM Modes in DS100BR111 Devices
The DS100BR111 supports reading directly from an external EEPROM device by implementing SMBus Master
mode. When using the SMBus master mode, the DS100 will read directly from specific location in the external
EEPROM. When designing a system for using the external EEPROM, the user needs to follow these specific
guidelines.
Set the DS100BR111 into SMBus Master Mode
–
Float ENSMB (PIN 3)
The external EEPROM device must support 400 KHz operation
The external EEPROM device address byte must be 0xA0'h
Set the AD[3:0] inputs for SMBus address byte. When the AD[3:0] = 0000'b, the device address byte is B0'h.
Based on the SMBus 2.0 specification, a device can have a 7-bit slave address of 1010 000'b. The LSB is set
to 0'b (for a WRITE). The bit mapping for SMBus is listed below:
–
[7:5] = Reserved Bits from the SMBus specification
–
[4:1] = Usable SMBus Address Bits
–
[0] = Write Bit
The DS100BR111 devices have AD[3:0] inputs in SMBus mode (pins 1, 2, 9, 10). These pins set SMBus
slave address. When the AD[3:0] = 0001'b, the device address byte is B2'h.
–
[7:5] = Default to 3b'101
–
[4:1] = Address of 4'b0001
–
[0] = Write Bit, 1'b0
The device address can be set with the use of the AD[3:0] input up to 16 different addresses. Use the
example below to set each of the SMBus addresses.
–
AD[3:0] = 0001'b, the device address byte is B2'h
–
AD[3:0] = 0010'b, the device address byte is B4'h
–
AD[3:0] = 0011'b, the device address byte is B6'h
–
AD[3:0] = 0100'b, the device address byte is B8'h
The master implementation in the DS100BR111 supports multiple devices reading from 1 EEPROM. When
tying multiple devices to the SDA and SCL pins, use these guidelines:
–
Use adjacent SMBus addresses for the 4 devices
–
Use a pull-up resistor on SDA; value = 4.7K
–
Use a pull-up resistor on SCL: value = 4.7K
–
Daisy-chain READEN# (pin 17) and DONE# (pin18) from one device to the next device in the sequence
1. Tie READEN# of the 1st device in the chain (U1) to GND
2. Tie DONE# of U1 to READEN# of U2
3. Tie DONE# of U2 to READEN# of U3
4. Tie DONE# of U3 to READEN# of U4
5. Optional: Tie DONE# of U4 to a LED to show each of the devices have been loaded successfully
Master EEPROM Mode in the DS100BR111
Below is an example of a 2 kbits (256 x 8-bit) EEPROM in hex format for the DS100BR111 device. The first 3
bytes of the EEPROM always contain a header common and necessary to control initialization of all devices
connected to the I2C bus. CRC enable flag to enable/disable CRC checking. There is a MAP bit to flag the
presence of an address map that specifies the configuration data start in the EEPROM. If the MAP bit is not
present the configuration data start address is derived from the DS100BR111 address and the configuration data
size. A bit to indicate an EEPROM size > 256 bytes is necessary to properly address the EEPROM. There are 37
bytes of data size for each DS100BR111 device.
18
Copyright 2011–2013, Texas Instruments Incorporated
Product Folder Links: DS100BR111
相关PDF资料 |
PDF描述 |
|---|---|
| DS10BR254TSQX/NOPB | IC LVDS REPEAT 1.5GBPS 1:4 40LLP |
| DS1210SN/T&R | IC CONTROLLER CHIP NV IND 16SOIC |
| DS1211SN+T&R | IC CONTROLLER 8-CHIP NV 20-SOIC |
| DS1212+ | IC CONTROLLER NV 16-CHIP 28-DIP |
| DS1213B | IC SMARTSOCKET 16K/64K 28-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS100BR210 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Ultra Low Power 10.3 Gbps 2-Channel Repeater with Input Equalization and Output De-Emphasis |
| DS100BR210EVK | 功能描述:其他开发工具 DS100BR210 EVAL BOARD RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| DS100BR210EVK/NOPB | 功能描述:其他开发工具 DS100BR210 EVAL BOARD RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| DS100BR210SQ | 制造商:TI 制造商全称:Texas Instruments 功能描述:Ultra Low Power 10.3 Gbps 2-Channel Repeater with Input Equalization and Output De-Emphasis |
| DS100BR210SQ/NOPB | 功能描述:IC REPEATER 10.3GBPS 2CH 24LLP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号缓冲器，中继器，分配器 系列:* 标准包装:160 系列:- 类型:转发器 Tx/Rx类型:以太网 延迟时间:- 电容 - 输入:- 电源电压:2.37 V ~ 2.63 V 电流 - 电源:60mA 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商设备封装:64-TQFP-EP（10x10） 包装:托盘 其它名称:Q5134101 |
发布紧急采购，3分钟左右您将得到回复。