参数资料
型号: DS1249Y-70
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: Static RAM
英文描述: 256K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA32
封装: 0.740 INCH, DIP-32
文件页数: 3/10页
文件大小: 286K
代理商: DS1249Y-70
DS1249Y/AB
2 of 8
READ MODE
The DS1249 devices execute a read cycle whenever WE (Write Enable) is inactive (high) and CE (Chip
Enable) and OE (Output Enable) are active (low). The unique address specified by the 18 address inputs
(A0 - A17) defines which of the 262,144 bytes of data is accessed. Valid data will be available to the eight
data output drivers within tACC (Access Time) after the last address input signal is stable, providing that
CE
and OE access times are also satisfied. If OE and CE access times are not satisfied, then data access
must be measured from the later-occurring signal ( CE or OE ) and the limiting parameter is either tCO for
CE
or tOE for OE rather than tACC.
WRITE MODE
The DS1249 executes a write cycle whenever the WE and CE signals are active (low) after address
inputs are stable. The later-occurring falling edge of CE or WE will determine the start of the write cycle.
The write cycle is terminated by the earlier rising edge of CE or WE . All address inputs must be kept
valid throughout the write cycle. WE must return to the high state for a minimum recovery time (tWR)
before another cycle can be initiated. The OE control signal should be kept inactive (high) during write
cycles to avoid bus contention. However, if the output drivers are enabled ( CE and OE active) then WE
will disable the outputs in tODW from its falling edge.
DATA RETENTION MODE
The DS1249AB provides full functional capability for VCC greater than 4.75 volts and write protects by
4.5 volts. The DS1249Y provides full-functional capability for VCC greater than 4.5 volts and write
protects by 4.25 volts. Data is maintained in the absence of VCC without any additional support circuitry.
The nonvolatile static RAMs constantly monitor VCC. Should the supply voltage decay, the NV SRAMs
automatically write protects themselves, all inputs become “don’t care,” and all outputs become high
impedance. As VCC falls below approximately 3.0 volts, a power switching circuit connects the lithium
energy source to RAM to retain data. During power-up, when VCC rises above approximately 3.0 volts,
the power switching circuit connects external VCC to the RAM and disconnects the lithium energy source.
Normal RAM operation can resume after VCC exceeds 4.75 volts for the DS1249AB and 4.5 volts for the
DS1249Y.
FRESHNESS SEAL
Each DS1249 device is shipped from Dallas Semiconductor with its lithium energy source disconnected,
guaranteeing full energy capacity. When VCC is first applied at a level greater than VTP, the lithium
energy source is enabled for battery backup operation.
相关PDF资料
PDF描述
DS1249Y-100 256K X 8 NON-VOLATILE SRAM MODULE, 100 ns, DMA32
DS1250W 512K X 8 NON-VOLATILE SRAM MODULE, 150 ns, DMA32
DS1250Y 512K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA32
DS1250AB 512K X 8 NON-VOLATILE SRAM MODULE, 70 ns, DMA32
DS1258AB-70 128K X 16 NON-VOLATILE SRAM MODULE, 70 ns, DMA40
相关代理商/技术参数
参数描述
DS1249Y-70# 功能描述:NVRAM 2048K NV SRAM RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube
DS1249Y-70IND 功能描述:NVRAM 2048K NV SRAM RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube
DS1249Y-70-IND 制造商:未知厂家 制造商全称:未知厂家 功能描述:NVRAM (Battery Based)
DS1249Y-70IND# 功能描述:NVRAM 2048K NV SRAM RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube
DS1249Y-85 功能描述:NVRAM 2048K NV SRAM RoHS:否 制造商:Maxim Integrated 数据总线宽度:8 bit 存储容量:1024 Kbit 组织:128 K x 8 接口类型:Parallel 访问时间:70 ns 电源电压-最大:5.5 V 电源电压-最小:4.5 V 工作电流:85 mA 最大工作温度:+ 70 C 最小工作温度:0 C 封装 / 箱体:EDIP 封装:Tube