- 您现在的位置：买卖IC网 > PDF目录9372 > DS1337U/T&R (Maxim Integrated Products)IC RTC SERIAL 2WIRE LP 8-USOP PDF资料下载
参数资料
| 型号： | DS1337U/T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/16页 |
| 文件大小： | 0K |
| 描述： | IC RTC SERIAL 2WIRE LP 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，方波输出，涓流充电器 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 电压 - 电源，电池： | 1.3 V ~ 1.8 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS1337 I
2C Serial Real-Time Clock
Bit 1: Alarm 2 Interrupt Enable (A2IE). When set to logic 1, this bit permits the alarm 2 flag (A2F) bit in the status
register to assert
INTA (when INTCN = 0) or to assert SQW/INTB (when INTCN = 1). When the A2IE bit is set to
logic 0, the A2F bit does not initiate an interrupt signal. The A2IE bit is disabled (logic 0) when power is first
applied.
Bit 0: Alarm 1 Interrupt Enable (A1IE). When set to logic 1, this bit permits the alarm 1 flag (A1F) bit in the status
register to assert
INTA. When the A1IE bit is set to logic 0, the A1F bit does not initiate the INTA signal. The A1IE
bit is disabled (logic 0) when power is first applied.
Status Register (0Fh)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
OSF
0
A2F
A1F
Bit 7: Oscillator Stop Flag (OSF). A logic 1 in this bit indicates that the oscillator either is stopped or was stopped
for some period of time and may be used to judge the validity of the clock and calendar data. This bit is set to logic
1 anytime that the oscillator stops. The following are examples of conditions that can cause the OSF bit to be set:
1) The first time power is applied.
2) The voltage present on VCC is insufficient to support oscillation.
3) The
EOSC bit is turned off.
4) External influences on the crystal (e.g., noise, leakage, etc.).
This bit remains at logic 1 until written to logic 0.
Bit 1: Alarm 2 Flag (A2F). A logic 1 in the alarm 2 flag bit indicates that the time matched the alarm 2 registers.
This flag can be used to generate an interrupt on either
INTA or SQW
/INTB depending on the status of the INTCN
bit in the control register. If the INTCN bit is set to logic 0 and A2F is at logic 1 (and A2IE bit is also logic 1), the
INTA pin goes low. If the INTCN bit is set to logic 1 and A2F is logic 1 (and A2IE bit is also logic 1), the SQW/INTB
pin goes low. A2F is cleared when written to logic 0. This bit can only be written to logic 0. Attempting to write to
logic 1 leaves the value unchanged.
Bit 0: Alarm 1 Flag (A1F). A logic 1 in the alarm 1 flag bit indicates that the time matched the alarm 1 registers. If
the A1IE bit is also logic 1, the
INTA pin goes low. A1F is cleared when written to logic 0. This bit can only be
written to logic 0. Attempting to write to logic 1 leaves the value unchanged.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1337S/T&R | IC RTC SERIAL 2WIRE LP 8-SOIC |
| DS1342T+T&R | IC RTC I2C W/ALARM 6TDFN |
| DS1341T+T&R | IC RTC I2C W/ALARM 6TDFN |
| DS1337U+T&R | IC RTC SERIAL 2WIRE LP 8-USOP |
| VI-J4X-MZ | CONVERTER MOD DC/DC 5.2V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1338 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:I2C RTC with 56-Byte NV RAM |
| DS1338_08 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with 56-Byte NV RAM |
| DS1338_11 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with 56-Byte NV RAM |
| DS1338_1203 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:I2C RTC with 56-Byte NV RAM |
| DS1338C-18 | 功能描述:实时时钟 I2C Serial RTC w/56 Byte NV RAM RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。