- 您现在的位置：买卖IC网 > PDF目录1994 > DS17285S-3NT (Maxim Integrated Products)IC RTC 3V 2K NV RAM 24-SOIC PDF资料下载
参数资料
| 型号： | DS17285S-3NT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/31页 |
| 文件大小： | 0K |
| 描述： | IC RTC 3V 2K NV RAM 24-SOIC |
| 标准包装： | 1,000 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，夏令时，闰年，NVSRAM，方波输出 |
| 存储容量： | 2KB |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | 并联 |
| 电源电压： | 2.7 V ~ 3.7 V |
| 电压 - 电源，电池： | 2.5 V ~ 3.7 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
DS17285/DS17287/DS17485/DS17487/DS17885/DS17887
Nonvolatile RAM
The user RAM bytes are not dedicated to any special
function within the DS17x85. They can be used by the
processor program as battery-backed memory and are
fully available during the update cycle.
The user RAM is divided into two separate memory
banks. When the bank 0 is selected, the 14 real-time
clock registers and 114 bytes of user RAM are accessi-
ble. When bank 1 is selected, an additional 2kbytes,
4kbytes, or 8kbytes of user RAM are accessible
through the extended RAM address and data registers.
Interrupts
The RTC includes six separate, fully automatic sources
of interrupt for a processor:
1) Alarm Interrupt
2) Periodic Interrupt
3) Update-Ended Interrupt
4) Wake-Up Interrupt
5) Kickstart Interrupt
6) RAM Clear Interrupt
The conditions that generate each of these indepen-
dent interrupt conditions are described in detail in other
sections of this data sheet. This section describes the
overall control of the interrupts.
The application software can select which interrupts, if
any, are to be used. There are 6 bits, including 3 bits in
Register B and 3 bits in Extended Register 4B, that
enable the interrupts. The extended register locations
are described later. Writing logic 1 to an interrupt-
enable bit permits that interrupt to be initiated when the
event occurs. A logic 0 in the interrupt-enable bit pro-
hibits the IRQ pin from being asserted from that interrupt
condition. If an interrupt flag is already set when an
interrupt is enabled, IRQ is immediately set at an active
level, although the event initiating the interrupt condition
might have occurred much earlier. Therefore, there are
cases where the software should clear these earlier
generated interrupts before first enabling new interrupts.
When an interrupt event occurs, the relating flag bit is
set to logic 1 in Register C or in Extended Register 4A.
These flag bits are set regardless of the setting of the
corresponding enable bit located either in Register B or
in Extended Register 4B. The flag bits can be used in a
polling mode without enabling the corresponding
enable bits.
However, care should be taken when using the flag bits
of Register C as they are automatically cleared to 0
immediately after they are read. Double latching is
implemented on these bits so that set bits remain sta-
ble throughout the read cycle. All bits that were set are
cleared when read and new interrupts that are pending
during the read cycle are held until after the cycle is
completed. One, two, or three bits can be set when
reading Register C. Each used flag bit should be exam-
ined when read to ensure that no interrupts are lost.
The flag bits in Extended Register 4A are not automati-
cally cleared following a read. Instead, each flag bit
can be cleared to 0 only by writing 0 to that bit.
When using the flag bits with fully enabled interrupts,
the IRQ line is driven low when an interrupt flag bit is
set and its corresponding enable bit is also set. IRQ is
held low as long as at least one of the six possible
interrupt sources has its flag and enable bits both set.
The IRQF bit in Register C is 1 whenever the IRQ pin is
being driven low as a result of one of the six possible
active sources. Therefore, determination that the
DS17x85/DS17x87 initiated an interrupt is accom-
plished by reading Register C and finding IRQF = 1.
IRQF remains set until all enabled interrupt flag bits are
cleared to 0.
Oscillator Control Bits
A pattern of 01X in bits 4 to 6 of Register A turns the
oscillator on and enables the countdown chain. A pat-
tern of 11X (DV2 = 1, DV1 = 1, DV0 = X) turns the oscil-
lator on, but holds the countdown chain of the oscillator
in reset. All other combinations of bits 4 to 6 keep the
oscillator off.
When the DS17x87 is shipped from the factory, the
internal oscillator is turned off. This feature prevents the
lithium energy cell from being used until it is installed in
a system.
Square-Wave Output Selection
Thirteen of the 15 divider taps are made available to a
1-of-16 multiplexer, as shown in Figure 1. The square
wave and periodic interrupt generators share the out-
put of the multiplexer. The RS0–RS3 bits in Register A
establish the output frequency of the multiplexer. These
frequencies are listed in Table 4. Once the frequency is
selected, the output of the SQW pin can be turned on
and off under program control with the square-wave
enable bit (SQWE).
If E32K = 0, the square-wave output is determined by
the RS3 to RS0 bits. If E32K = 1, a 32kHz square wave
is output on the SQW pin, regardless of the RS3 to RS0
bits’ state. If E32K = ABE = 1 and a valid voltage is
applied to VBAUX, a 32kHz square wave is output on
SQW when VCC is below VTP.
Real-Time Clocks
18
____________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| DS1742-100IND | IC RTC RAM Y2K 5V 100NS 24-EDIP |
| DS1743P-70+ | IC RTC RAM Y2K 5V 70NS 34-PCM |
| DS1744-70IND | IC RTC RAM Y2K 5V 70NS 28-EDIP |
| DS1746-70IND | IC RTC RAM Y2K 5V 70NS 32-EDIP |
| DS1747W-120IND | IC RTC RAM Y2K 3.3V 120NS 32EDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS17285S-5 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS17285S-5/T&R | 制造商:Maxim Integrated Products 功能描述:IC RTC 5V 2K NV RAM 24-SOIC |
| DS17285S-5/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS17285S-5+ | 功能描述:实时时钟 3V/5V RTC K Multiplexed Kick-S RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS17285S-5+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK MULTIPLEXED 2KBYTE 24SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Maxim Integrated DS17285S-5+T&R Real Time Clocks (RTC) 制造商:Maxim Integrated Products 功能描述:IC RTC 5V 2K NV RAM 24-SOIC |
发布紧急采购，3分钟左右您将得到回复。