- 您现在的位置：买卖IC网 > PDF目录1913 > DS1808Z-050/T&R (Maxim Integrated Products)IC POT DUAL LOG HV 50K 16-SOIC PDF资料下载
参数资料
| 型号： | DS1808Z-050/T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/17页 |
| 文件大小： | 0K |
| 描述： | IC POT DUAL LOG HV 50K 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 接片： | 32 |
| 电阻（欧姆）： | 45k |
| 电路数： | 2 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 4.5 V ~ 5.5 V，±4.5 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
DS1808
6 of 17
The master device generates all serial clock pulses and the start and stop conditions. A transfer is ended
with a stop condition or with a repeated start condition. Since a repeated start condition is also the
beginning of the next serial transfer, the bus will not be released.
The DS1808 may operate in the following two modes:
1. Slave receiver mode: Serial data and clock are received through SDA and SCL respectively. After
each byte is received, an acknowledge bit is transmitted. Start and stop conditions are recognized as
the beginning and end of a serial transfer. Address recognition is performed by hardware after
reception of the slave (device) address and direction bit.
2. Slave transmitter mode: The first byte is received and handled as in the slave receiver mode.
However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data
is transmitted on SDA by the DS1808 while the serial clock is input on SCL. Start and stop conditions
are recognized as the beginning and end of a serial transfer.
3. Slave Address: command/control byte is the first byte received following the start condition from the
master device. The command/control byte consists of a 4-bit control code. For the DS1808, this is set
as 0101 binary for read/write operations. The next three bits of the command/control byte are the
device select bits or slave address (A2, A1, A0). They are used by the master device to select which
of eight devices is to be accessed. When reading or writing the DS1808, the device select bits must
match the device select pins (A2, A1, A0). The last bit of the command/control byte (R/W) defines
the operation to be performed. When set to a 1, a read operation is selected, and when set to a 0, a
write operation is selected.
Following the START condition, the DS1808 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 0101 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an acknowledge signal on the SDA line.
COMMAND AND PROTOCOL
The command and protocol structure of the DS1808 allows the user to read from or write to the
potentiometer(s). Additionally, the 2-wire command/protocol structure of the DS1808 will support eight
different devices and a maximum of 16 channels that can be uniquely controlled. The command
structures for the device are presented in Figures 3, 4, 5, and 6. Potentiometer data values and
command/control values are always transmitted most significant bit (MSB) first. During communications,
the receiving unit always generates the acknowledgement.
相关PDF资料 |
PDF描述 |
|---|---|
| DS1809U-100/T&R | IC DALLASTAT NV 100KOHM 8-USOP |
| DS1841N+ | IC RES LOG NV I2C 5.5V 10-TDFN |
| DS1844S-100/T&R | IC POT DIG QUAD 100K 20-SOIC |
| DS1845E-100/T&R | IC POT/MEM DUAL NV 100K 14-TSSOP |
| DS1846E-010+T&R | IC NV TRI-POT MEM MON 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1809 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Dallastat, 64-position linear taper |
| DS1809-010 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1809-010+ | 功能描述:数字电位计 IC Dallastat RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1809-050 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1809-050+ | 功能描述:数字电位计 IC Dallastat RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。