参数资料
| 型号： | DS1841X |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/17页 |
| 文件大小： | 0K |
| 描述： | IC RES LOG NV I2C DGTL 10TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 接片： | 128 |
| 电阻（欧姆）： | 22k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±250 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 模具 |
| 供应商设备封装： | 模具 |
| 包装： | 管件 |
DS1841
Temperature-Controlled, NV, I2C,
Logarithmic Resistor
______________________________________________________________________________________
11
Register 03h: Control Register 1 (CR1)
FACTORY DEFAULT
03h
MEMORY TYPE
Shadowed NV
03h
Reserved
Adder Mode
Update Mode
Bit 7
Bit 0
Bits 7 to 2
Reserved.
Bit 1
Adder Mode This bit is valid only if the Update Mode bit = 1.
0 = The LUTVAL or IVR value is directly loaded to WR though the mux.
1 = (Default) The LUTVAL is summed with the IVR value and is directly loaded to WR though the mux.
Bit 0
Update Mode
0 = CR0 is enabled. During power-up the IVR value is loaded into the WR to set the wiper position.
Updates to Temperature Result (0Ch) and Supply Voltage Result (0Eh) are halted.
1 = (Default) The WR is controlled directly by I2C communication though registers 08h or 09h, or the WR
is controlled by the temperature-compensation/LUT circuitry. If temperature compensation is enabled,
one of the 72 temperature slots is selected (by the LUTAR) and this slot value is copied into the
LUTVAL, which in turn sets the WR. Updates to Temperature Result (0Ch) and Supply Voltage Result
(0Eh) are enabled.
Control Register 1 controls how the wiper position is determined. The
SEE bit controls whether the values of this register
are stored in EEPROM or in Shadowed SRAM. On power-up, the EEPROM value is recalled to this register, regardless of
the state of
SEE.
While the registers other than 00h through 0Ah can be read, they are not updated by the ADC as the ADC is disabled
with the Update Mode bit = 0.
Register 08h: LUT Address Register (LUTAR)
FACTORY DEFAULT
00h
POR DEFAULT
00h until tFRAME
MEMORY TYPE
Volatile
08h
LUTAR
Bit 7
Bit 0
The LUTAR register serves as the index pointer to choose the corresponding temperature slot in the LUT based on the
internal temperature sensor result. The LUTAR can be directly read by acessing address 08h; however, to write an new
value to LUTAR (to control WR manually), the LUTAR Mode bit must be set to a 1.
Register 09h: LUT Value Register (WR*)
FACTORY DEFAULT
00h
MEMORY TYPE
Volatile
09h
WR*
Bit 7
Bit 0
WR serves as an intermediate location, which is populated automatically with the results of the temperature-indexed
lookup. The WR can be directly read by acessing address 09h; however to write an new value to WR (to control it
manually), the wiper access control bit must be set to a 1. WR is an unsigned 7-bit value.
*WR is updated every tFRAME if Update Mode bit = 1. If Update Mode bit = 0, WR holds the value stored in register 00h.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-2V2-MX-B1 | CONVERTER MOD DC/DC 15V 75W |
| VI-2V3-MX-B1 | CONVERTER MOD DC/DC 24V 75W |
| DS3501U+T&R | IC POT NV 128POS HV 10-USOP |
| DS3502U+T&R/C | IC POT DGTL NV 128TAP 10-USOP |
| DS3502U+T&R | IC POT DGTL NV 128TAP 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1842 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:76V, APD, Bias Output Stage with Current Monitoring |
| DS1842A | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:76V, APD, Bias Output Stage with Current Monitoring |
| DS1842AN+ | 功能描述:电流和电力监控器、调节器 76V APD Bias Output Stage w/Current Mtr RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| DS1842AN+T&R | 制造商:Maxim Integrated Products 功能描述:76V, APD, BIAS OUTPUT STAGE WITH CURRENT MONITORING - Tape and Reel |
| DS1842AN+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:76V, APD, Bias Output Stage with Current Monitoring |
发布紧急采购，3分钟左右您将得到回复。