- 您现在的位置：买卖IC网 > PDF目录9058 > DS1844-100 (Maxim Integrated Products)IC POT DIG QUAD 100K 20-DIP PDF资料下载
参数资料
| 型号： | DS1844-100 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC POT DIG QUAD 100K 20-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 18 |
| 接片： | 64 |
| 电阻（欧姆）： | 100k |
| 电路数： | 4 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 2 线串行（设备位址）或 5 线串行 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
DS1844
5 of 14
SLAVE ADDRESS
A command/control byte is the 1st byte received following the START condition from the master device.
The command/control byte consists of a 4-bit control code. For the DS1844, this is set as 0101 binary for
read/write operations. The next 3 bits of the command/ control byte are the device select bits or slave
address (A2, A1, A0). They are used by the master device to select which of eight devices is to be
accessed. When reading or writing the DS1844, the device-select bits must match the device-select pins
(A2, A1, A0). The last bit of the command/control byte (R/W) defines the operation to be performed.
When set to a 1 a read operation is selected, and when set to a 0 a write operation is selected. Figure 5
shows the command/control byte structure for the DS1844.
Following the START condition, the DS1844 monitors the SDA bus checking the device type identifier
being transmitted. Upon receiving the 0101 control code, the appropriate device address bits, and the
read/write bit, the slave device outputs an acknowledge signal on the SDA line.
COMMAND AND PROTOCOL
The command and protocol structure of the DS1844 allows the user to read or write the potentiometer(s).
Additionally, the 2-wire command/protocol structure of the DS1844 will support eight different devices
and a maximum of 32 channels that can be uniquely controlled. The command structures for the device
are presented in Figures 6 and 7. Potentiometer data values and control and command values are always
transmitted most significant bit (MSB) first. During communications, the receiving unit always generates
the acknowledgement.
Reading the DS1844
As shown in Figure 6, the DS1844 provides one read command operation. This operation allows the user
to read all potentiometers. Specifically, the R/W bit of the command/control byte is set equal to a 1 for a
read operation. Communication to read the DS1844 begins with a START condition which is issued by
the master device. The command/control byte from the master device will follow the START condition.
Once the command/control byte has been received by the DS1844, the part will respond with an
ACKNOWLEDGE. The read/write bit of the command/control byte, as stated, should be set equal to 1
for reading the DS1844.
When the master has received the ACKNOWLEDGE from the DS1844, the master can then begin to
receive potentiometer wiper data. The value of the potentiometer-0 wiper position will be the first
returned from the DS1844, followed by potentiometer-1 and so forth. Once the 8 bits of the
potentiometer-0 wiper position have been transmitted, the master will need to issue an
ACKNOWLEDGE, unless it is the only byte to be read, in which case the master issues a NOT
ACKNOWLEDGE. If desired the master may stop the communication transfer at this point by issuing the
STOP condition. However, if the value of the remaining potentiometers is needed, transfer can continue
by clocking the 8 bits of the potentiometer-1 value, followed by an ACKNOWLEDGE, and so forth.
Final communication transfer is terminated by issuing the STOP command. Again, the flow of the read
operation is presented in Figure 6.
Writing the DS1844
A data flow diagram for writing the DS1844 is shown in Figure 7. The DS1844 has one write command
that is used to change the position(s) of the wiper. The 2-wire serial interface write structure is similar to
that of the 5-wire serial write. However, there are differences.
All the write operations begin with a START condition. Following the START condition, the master
device will issue the command/control byte. The read/write bit of the command/control byte will be set to
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/95W08038 | CONN PLUG 3POS STRAIGHT W/SCKT |
| DS1844-050 | IC POT DIG QUAD 50K 20-DIP |
| M83723/95R08036 | CONN PLUG 3POS STRAIGHT W/SCKT |
| DS1844-010 | IC POT DIG QUAD 10K 20-DIP |
| DS1808Z-050 | IC POT DUAL LOG HV 50K 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1844-100+ | 功能描述:数字电位计 IC Quad RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1844-100E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1844-100S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1844-10E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1844-10S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
发布紧急采购，3分钟左右您将得到回复。