- 您现在的位置：买卖IC网 > PDF目录9058 > DS1844-100 (Maxim Integrated Products)IC POT DIG QUAD 100K 20-DIP PDF资料下载
参数资料
| 型号： | DS1844-100 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | IC POT DIG QUAD 100K 20-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 18 |
| 接片： | 64 |
| 电阻（欧姆）： | 100k |
| 电路数： | 4 |
| 温度系数： | 标准值 750 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 2 线串行（设备位址）或 5 线串行 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 20-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 20-PDIP |
| 包装： | 管件 |
DS1844
2 of 14
The DS1844 is available in standard 10 k
W, 50 kW, and 100 kW versions. Mixed resistor combinations
are also available through custom setups. The DS1844 is specified to operate over the industrial
temperature range: -40
°C to +85°C. Packages for the DS1844 include 20-pin DIPs, SOICs, and TSSOPs.
OPERATION
The DS1844 contains four 64-position potentiometers. Each potentiometer is independent and has three
accessible terminals, which include HX, LX, and WX. Each potentiometer is comprised of 63 individual
resistor elements. Between each resistor element is a tap-point that is multiplexed to the wiper terminal,
WX. Additionally, the wiper terminal can be multiplexed directly to the end-terminals, HX and LX.
The DS1844 supports two interface control options. Both options allow for the direct placement of the
wiper position on the resistor ladder. Each wiper has an associated 6-bit register used to hold its positional
value.
The DS1844 is a volatile device and will always power-up with the wiper positions set to mid-tap
(position 32-decimal). The end-terminal HX will have wiper position value 63-decimal and the LX terminal
will have wiper position value 0-decimal. Because the DS1844 is a 64-position device only 6 bits of data
are necessary to write a wiper’s value. However, communication with the DS1844 will require using a
full 8 bits, with the remaining 2 bits specifying the potentiometer selected. A discussion of proper
communication protocol is provided under the section entitled Serial Port Operation. A block diagram of
the DS1844 is shown in Figure 1.
SERIAL PORT OPERATION
As stated, the DS1844 can support two types of serial interface control. This includes a 5-wire serial
interface and a 2-wire addressable interface. The type interface supported during operation is selectable
via the port select input pin, PS. Additionally, certain pins provide dual functionality dependent on the
serial port selected. The pin description table lists pin functionality according to the interface selected.
5-Wire Serial Port Control
The 5-wire serial interface provides an 8-bit I/O shift register for loading and reading wiper data. The 5-
wire serial interface control is selected when the port select input, PS, is in a low state. This interface is
controlled by the signals RST , DIN, DOUT, CLK, and R/ W . Timing diagrams for the 5-wire serial port
can be found in Figure 3. Timing information for the 5-wire serial port is provided in the AC Electrical
Characteristics table for 5-wire serial communications.
Data is loaded MSB first and in multiples of 8 bits. The 8-bit data to specify wiper position has the format
or protocol as that shown in Figure 2. The 8-bit data is divided into potentiometer select data and wiper
position value. The 6 least significant bits of data specify the wiper position value while the 2 most
significant bits specify the potentiometer to be loaded. This allows the interface control logic/protocol to
provide order independent potentiometer loading, as well as variable-length data loads.
As stated earlier, the 5-wire serial port is selected when the PS input is in a low state. If the device will
only be used in the 5-wire mode, the PS input can be tied directly to ground. Communication via the 5-
wire interface is enabled when RST is in a high state. A low-to-high transition on the RST indicates the
start of a communication transaction with the DS1844. While RST is high, data can be read or written to
the part. Data will be read or written dependent on the state of the read-write enable input, R/ W . The
state of R/ W must be stable before a low-to-high transition on RST . Once the RST input has begun a
communication transaction, the serial port will ignore any transitions on the R/ W input.
相关PDF资料 |
PDF描述 |
|---|---|
| M83723/95W08038 | CONN PLUG 3POS STRAIGHT W/SCKT |
| DS1844-050 | IC POT DIG QUAD 50K 20-DIP |
| M83723/95R08036 | CONN PLUG 3POS STRAIGHT W/SCKT |
| DS1844-010 | IC POT DIG QUAD 10K 20-DIP |
| DS1808Z-050 | IC POT DUAL LOG HV 50K 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1844-100+ | 功能描述:数字电位计 IC Quad RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS1844-100E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1844-100S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1844-10E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
| DS1844-10S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Digital Potentiometer |
发布紧急采购，3分钟左右您将得到回复。