- 您现在的位置：买卖IC网 > PDF目录20033 > DS1861B+ (Maxim Integrated)IC LASR CTRLR 1CHAN 5.5V 16CSBGA PDF资料下载
参数资料
| 型号： | DS1861B+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 15/25页 |
| 文件大小： | 0K |
| 描述： | IC LASR CTRLR 1CHAN 5.5V 16CSBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 810 |
| 类型： | 激光二极管控制器（光纤） |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 电源： | 5mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 16-LBGA，CSPBGA |
| 供应商设备封装： | 16-CSBGA（4x4） |
| 包装： | 托盘 |
| 安装类型： | 表面贴装 |
Full Laser Control with Fault Management
Figure 11 shows the extinction ratios (expressed in
decibels) as a function of N for several A M /A D ratios.
Note the actual extinction ratio value is determined by
the ratio A M /A D in addition to N. If the A M /A D ratio
varies due to voltage, temperature, or aging effects, it
becomes an additional error source when determining
the overall extinction ratio variance. The DS1861 is
25
20
EXTINCTION RATIO (AM/AD = 1.2)
vs. ER SETTING
meant to be used with a monolithic laser driver, where
A M and A D are generated on the same chip, so
changes in the ratio of A M to A D are minimal.
The N value itself is determined by the extinction ratio
register. There are two components of the ER register
used to calculate N. The range select bit (RSEL), which
selects the high (RSEL = 1) or low (RSEL = 0) range of
15
10
5
RSEL = 0
N, is the MSB of the register. The lower seven bits of
the register (ER<6:0>) determine the value of N within
the selected range. The value of N is given by:
0
16
32
48 64 80
ER SETTING (DECIMAL)
96
112
EXTINCTION RATIO (AM/AD = 0.8)
? ER < 6 : 0 > + 32
N = ?
? ER < 6 : 0 > + 32 when RSEL = 1
? when RSEL = 0
2
?
The ER<6:0> value should be programmed to values
between 28 and 104 (decimal), regardless if the high or
low range is selected, to ensure that the N value
remains accurate and constant as intended. These lim-
its allow the N values of the high and low range to over-
lap to ensure that all N values can be attained, but
prevents potential errors that can be caused by using
25
20
15
10
5
RSEL = 1
vs. ER SETTING
RSEL = 0
the extremes of each RSEL range. Figure 12 shows the
N values as a function of the ER register setting.
0
16
32
48 64 80
ER SETTING (DECIMAL)
96
112
The Convergence Algorithm and
Overshoot Control
The DS1861 uses a tiered slew-rate control system that
adjusts the DAC update rate and the number of LSBs it
increases/decreases per update cycle when the control
loop is seeking to converge to its steady state value. For
the APC loop, it makes its decision on the required con-
25
20
EXTINCTION RATIO (AM/AD = 0.4)
vs. ER SETTING
vergence rate based on the percent error between the
present BMD current and the BMD current-set point.
The modulation current slew rate is adjusted based
solely on the difference between its present code and
15
10
RSEL = 1
the code-set point that is determined by the AERC cir-
cuitry. Both update rates are designed to prevent any
overshoot during large set-point changes in excess of
5
RSEL = 0
10%, which assumes (see the following) the ratio of the
laser diode’s threshold current (I TH ) to the average
power current (I APC ) is below 7:1. Most systems do not
0
16
32
48 64 80
ER SETTING (DECIMAL)
96
112
exhibit any overshoot when using the DS1861.
Figure 11. Typical Extinction Ratios vs. N Codes
____________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| HCC35DRAS-S734 | CONN EDGECARD 70POS .100 R/A PCB |
| T86C225M025EBSS | CAP TANT 2.2UF 25V 20% 2312 |
| VE-24Z-CV-F4 | CONVERTER MOD DC/DC 2V 60W |
| DS1863E+T&R | IC LASR CTRLR 1CHAN 5.5V 16TSSOP |
| QPI-10LZ-01 | IC HOT SWAP EMI FILTER 10LGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1861B+ | 功能描述:激光驱动器 Closed Loop Laser Control RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1861E | 制造商:Maxim Integrated Products 功能描述:LASER DRVR 1CH 14TSSOP - Rail/Tube |
| DS1861E+ | 功能描述:激光驱动器 Closed Loop Laser Control RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862A | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
发布紧急采购，3分钟左右您将得到回复。