参数资料
| 型号： | DS1861E+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 21/25页 |
| 文件大小： | 0K |
| 描述： | IC LASR CTRLR 1CHAN 5.5V 14TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 类型： | 激光二极管控制器（光纤） |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 电源： | 5mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
Full Laser Control with Fault Management
I 2 C Definitions
The following terminology is commonly used to
describe I 2 C data transfers.
Master Device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses, and start and stop conditions.
Slave Devices: Slave devices send and receive data
at the master’s request.
Bus Idle or Not Busy: Time between stop and start
conditions when both SDA and SCL are inactive and in
their logic-high states.
Start Condition: A start condition is generated by the
master to initiate a new data transfer with a slave.
Transitioning SDA from high to low while SCL remains
high generates a start condition. See the timing dia-
gram for applicable timing.
Stop Condition: A stop condition is generated by the
master to end a data transfer with a slave. Transitioning
SDA from low to high while SCL remains high gener-
ates a stop condition. See the timing diagram for
applicable timing.
Repeated Start Condition: The master can use a
repeated start condition at the end of one data transfer to
indicate that it will immediately initiate a new data trans-
fer following the current one. Repeated starts are com-
monly used during read operations to identify a specific
memory address to begin a data transfer. A repeated
SDA
start condition is issued identically to a normal start con-
dition. See the timing diagram for applicable timing.
Bit Write: Transitions of SDA must occur during the low
state of SCL. The data on SDA must remain valid and
unchanged during the entire high pulse of SCL plus the
setup and hold time requirements (Figure 14). Data is
shifted into the device during the rising edge of the SCL.
Bit Read: At the end of a write operation, the master
must release the SDA bus line for the proper amount of
setup time (Figure 14) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master gener-
ates all SCL clock pulses including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK): An
Acknowledgement (ACK) or Not Acknowledge (NACK)
is always the 9th bit transmitted during a byte transfer.
The device receiving data (the master during a read or
the slave during a write operation) performs an ACK by
transmitting a zero during the 9th bit. A device per-
forms a NACK by transmitting a one during the 9th bit.
Timing (Figure 14) for the ACK and NACK is identical to
all other bit writes. An ACK is the acknowledgment that
the device is properly receiving data. A NACK is used
to terminate a read sequence or as an indication that
the device is not receiving data.
t BUF
t HD:STA
t SP
SCL
t LOW
t R
t F
t HD:STA
t HIGH
t SU:STA
STOP
START
t SU:DAT
REPEATED
START
t SU:STO
t HD:DAT
NOTE: TIMING IS REFERENCE TO V IL(MAX) AND V IH(MIN) .
Figure 14. I 2 C Timing Diagram
____________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| DS1862AB+ | IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1862B+T&R | IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
| DS1873T+ | IC CTLR SFP+ ANLG LDD 28-TQFN |
| DS1874T+ | IC CTLR SFP+ ANLG LDD 28-TQFN |
| DS2129S+T&R | IC REGULATOR SCSI 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1861E+ | 功能描述:激光驱动器 Closed Loop Laser Control RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862A | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:XFP Laser Control and Digital Diagnostic IC |
| DS1862AB+ | 功能描述:激光驱动器 XFP Laser Control & Digital Diagnostic RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| DS1862AB+T&R | 制造商:Maxim Integrated Products 功能描述:XFP LASER CONTROL 25CSBGA - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC LASR CTRLR 7CHAN 5.5V 25CSBGA |
发布紧急采购，3分钟左右您将得到回复。