- 您现在的位置：买卖IC网 > PDF目录20033 > DS1863E+T&R (Maxim Integrated)IC LASR CTRLR 1CHAN 5.5V 16TSSOP PDF资料下载
参数资料
| 型号： | DS1863E+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/62页 |
| 文件大小： | 0K |
| 描述： | IC LASR CTRLR 1CHAN 5.5V 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 激光二极管控制器 |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 5.5 V |
| 电流 - 电源： | 5mA |
| 电流 - 偏置： | 1.2mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
Burst-Mode PON Controller
With Integrated Monitoring
FETG/OUTPUT DISABLE TIMING (FAULT CONDITION DETECTED)
DETECTION OF
FETG FAULT
TX-D
I BIAS
I MOD
FETG
t OFF
t OFF
t FETG:ON
t ON
t ON
t FETG:OFF
Figure 6. FETG/Modulation and Bias Timing (Fault Condition Detected).
higher level is an Analog POR (V POA ). At start up,
before the supply voltage rises above V POA , the out-
puts are disabled (FETG and BIAS outputs are high
impedance, MOD is low), all SRAM outputs are low
(including Shadowed EEPROM), and all analog circuit-
ry is disabled. When V CC reaches V POA , the SEE is
recalled, and the analog circuitry is enabled. While
V CC remains above V POA , the device is in its normal
operating state, and it responds based on its non-
volatile configuration. If during operation V CC falls
below V POA , but is still above V POD , then the SRAM
will retain the SEE settings from the first SEE recall, but
the device analog will be shut down and the outputs
disabled. FETG will be driven to its alarm state defined
by the FETG DIR bit (Table 02h, Register 89h). If the
supply voltage recovers back above V POA , then the
device will immediately resume normal functioning. If
the supply voltage falls below V POD , then the device
SRAM will be placed in its default state and another
SEE recall will be required to reload the nonvolatile set-
tings. The EEPROM recall will occur the next time V CC
next exceeds V POA . Figure 7 shows the sequence of
events as the voltage varies.
Any time V CC is above V POD , the I 2 C interface can be
used to determine if V CC is below the V POA level. This
is accomplished by checking the RDYB bit in the Status
(6Eh) byte. RDYB is set when V CC is below V POA ; when
V CC rises above V POA RDYB is timed (within 500μs) to
go to 0, at which point the part is fully functional.
For all Device Addresses sourced from EEPROM (Byte
8Ch, Table 01h in memory) the default Device Address
is A2h until V CC exceeds V POA allowing the device
address to be recalled from the EEPROM.
Power-On Analog (POA)
POA holds the DS1863 in reset until V CC is at a suitable
level (V CC > V POA ) for the part to accurately measure
with its ADC and compare analog signals with its quick-
trip monitors. Because V CC cannot be measured by the
ADC when V CC is less than V POA , POA also asserts the
V CC low alarm, which must be cleared by a V CC ADC
conversion that is greater than the customer programma-
ble V CC low ADC limit. This prevents the TX-F and FETG
outputs from glitching during a slow power up. The TX-F
and FETG output will not latch until there is a conversion
above V CC low limit.
The POA alarm is non-maskable. The TX-F, and FETG
outputs shuts off any time V CC is below V POA . See Low
Voltage Operation section for more information.
14
____________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| QPI-10LZ-01 | IC HOT SWAP EMI FILTER 10LGA |
| GMM44DRES | CONN EDGECARD 88POS .156 EYELET |
| VE-J0W-CY-B1 | CONVERTER MOD DC/DC 5.5V 50W |
| T86C225K025EBSS | CAP TANT 2.2UF 25V 10% 2312 |
| ABC31DRXH-S734 | CONN EDGECARD 62POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1863K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS1863T+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS1864 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:SFP Laser Controller and Diagnostic IC |
| DS1864K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS1864T | 制造商:Maxim Integrated Products 功能描述:DUAL TMP CTRL DAC+MONITORS,QFN - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。