- 您现在的位置：买卖IC网 > PDF目录18728 > DS1870E-010+ (Maxim Integrated)IC CNTRLR RF POWER AMP 16TSSOP PDF资料下载
参数资料
| 型号： | DS1870E-010+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 21/28页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR RF POWER AMP 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| RF 型： | 手机 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1431 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页
LDMOS RF Power-Amplifier Bias
Controller
A2D Value 0
Temp Value
V CC Value
VD Value
ID1 Value
A2D Value 1
ID2 Value
Status
Hi Alarm
<R><NA><0000h> The signed 2’s complement direct-to-temperature measurement.
<R><NA><0000h> Unsigned V CC voltage measurement.
<R><NA><0000h> Unsigned V D voltage measurement.
<R><NA><0000h> Unsigned I D1 voltage measurement.
<R><NA><0000h> Unsigned I D2 voltage measurement.
<R><NA><00h> High-Alarm Status bits.
a) Temp Hi High-alarm status for temperature measurement.
b) V CC Hi High-alarm status for V CC measurement.
c) VD Hi High-alarm status for V D measurement.
d) ID1 Hi High-alarm status for I D1 measurement.
e) ID2 HI High-alarm status for I D2 measurement.
Lo Alarm
<R><NA><40h> Low-Alarm Status bits.
a) Temp Lo Low-alarm status for temperature measurement.
b) V CC Lo Low-alarm status for V CC measurement. This bit is set when the V CC supply is below
the POR trip-point value. It clears itself when a V CC measurement is completed and
the value is above the low threshold.
c) VD Lo Low-alarm status for V D measurement.
d) ID1 Lo Low-alarm status for I D1 measurement.
e) ID2 Lo Low-alarm status for I D2 measurement.
I/O Status
<R><NA><see below> Status of the FAULT pin.
a) Fault Logical value of the FAULT pin. Fault is logic HIGH during power-on.
b) Mint Maskable Interrupt. FAULT is an open-drain output. In case FAULT was pulled low
externally or was missing the external pullup resistor, this bit reflects the logical value
the DS1870 is trying to output on the FAULT pin. If any ‘Hi Alarm’ or ‘Lo Alarm’ is
active and its corresponding ‘Fault Ena’ bit is enabled, or ‘RDBY’ is a 1, then this bit is
active high. Otherwise, this bit is a zero.
c) Rdyb Ready Bar. When the supply is above the power-on-analog (V POA ) trip point, this bit is
active low. Thus, this bit reads a logic 1 if the supply is below V POA or too low to com-
municate over the I 2 C bus.
A2D Status
<R/W><V><00h> Status of completed conversions. At power-on, these bits are cleared and are
set as each conversion is completed. These bits can be cleared so that completion
of new conversions may be verified.
a) Temp Rdy Temperature conversion is ready.
b) V CC Rdy V CC conversion is ready.
c) VD Rdy V D conversion is ready.
d) ID1 Rdy I D1 conversion is ready.
e) ID2 Rdy I D2 conversion is ready.
____________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| GLEB01A2B | SWITCH SIDE-ROTRY ROLL SNAP SPDT |
| GLEB01A5B | SWITCH SIDE-ROTRY ROLL SNAP SPDT |
| F5KA833M0D4MG-Z | FILTER SAW 833MHZ CDMA2000 |
| MAX2530ETI+ | IC LNA/MIXER CELL/PCS/GPS 28TQFN |
| UPC2746TB-E3-A | MMIC AMP 1.5GHZ SOT-363 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1870E-010+ | 功能描述:特殊用途放大器 LDMOS RF Power-Amp Bias Controller RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| DS1870E-010+T&R | 制造商:Maxim Integrated Products 功能描述:LDMOS RF PWR-AMP BIAS CNTRLR 16TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC RF PWR CNTRL PA 16TSSOP |
| DS1870E-010+T&R | 功能描述:特殊用途放大器 LDMOS RF Power-Amp Bias Controller RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| DS1870K | 制造商:Maxim Integrated Products 功能描述:DS1870 EVALUATION KIT - Bulk |
| DS1873 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SFP+ Controller with Analog LDD Interface |
发布紧急采购，3分钟左右您将得到回复。