- 您现在的位置：买卖IC网 > PDF目录20033 > DS1874T+T&R (Maxim Integrated)IC CTLR SFP+ ANLG LDD 28-TQFN PDF资料下载
参数资料
| 型号： | DS1874T+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/88页 |
| 文件大小： | 0K |
| 描述： | IC CTLR SFP+ ANLG LDD 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 激光二极管控制器 |
| 通道数： | 1 |
| 电源电压： | 2.85 V ~ 3.9 V |
| 电流 - 电源： | 2.5mA |
| 工作温度： | -40°C ~ 95°C |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
| 其它名称： | 90-1874T+TRL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
SFP+ Controller with Digital LDD Interface
BIAS and MODULATION Control
During Power-Up
The DS1874 has two internal registers, MODULATION
and BIAS, that represent the values written to the
MAX3798/MAX3799’s modulation DAC and bias DAC
through the 3-wire interface. On power-up, the DS1874
sets the MODULATION and BIAS registers to 0. When
V CC is above POA, the DS1874 initializes the MAX3798/
MAX3799. After a temperature conversion is completed
and if the VCC LO alarm is enabled, an additional V CC
conversion above the customer-defined VCC LO alarm
level is required before the MAX3798/MAX3799 MODU-
LATION register is updated with the value determined
by the temperature conversion and the modulation LUT.
When the MODULATION register is set, the BIAS regis-
ter is set to a value equal to ISTEP (see Figure 2). The
startup algorithm checks if this bias current causes a
feedback voltage above the APC set point, and if not, it
continues increasing the BIAS register by ISTEP until the
APC set point is exceeded. When the APC set point is
exceeded, the device begins a binary search to quickly
reach the bias current corresponding to the proper
power level. After the binary search is completed, the
APC integrator is enabled and single LSB steps are
used to tightly control the average power.
The TXP HI, TXP LO, HBAL, and BIAS MAX QT alarms
are masked until the binary search is completed.
However, the BIAS MAX alarm is monitored during this
time to prevent the BIAS register from exceeding
IBIASMAX. During the bias current initialization, the
BIAS register is not allowed to exceed IBIASMAX. If this
occurs during the ISTEP sequence, then the binary
search routine is enabled. If IBIASMAX is exceeded
during the binary search, the next smaller step is acti-
vated. ISTEP or binary increments that would cause the
BIAS register to exceed IBIASMAX are not taken.
Masking the alarms until the completion of the binary
search prevents false positive alarms during startup.
ISTEP is programmed by the customer using Table
02h, Register BBh. During the first steps, the MAX3798/
MAX3799 ’s bias DAC is directly written using
SET_IBIAS (3-wire address 09h). ISTEP should be pro-
grammed to the maximum safe increase that is allow-
able during startup. If this value is programmed too
low, the DS1874 still operates, but it could take signifi-
cantly longer for the algorithm to converge and hence
to control the average power.
If a fault is detected, and TXD is toggled to reenable
the outputs, the DS1874 powers up following a similar
sequence to an initial power-up. The only difference is
that the DS1874 already has determined the present
temperature, so the t INIT time is not required for the
DS1874 to recall the APC and MOD set points from
EEPROM.
V CC
V POA
t INIT
MODULATION REGISTER
t SEARCH
4x ISTEP
BIAS REGISTER
3x ISTEP
2x ISTEP
ISTEP
BINARY SEARCH
APC INTEGRATOR ON
BIAS SAMPLE
1
2
3
4
5
6
7
8
9
10
11
12
13
Figure 2. Power-Up Timing
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| HSC25DRAN-S734 | CONN EDGECARD 50POS .100 R/A PCB |
| HCC43DRTI-S93 | CONN EDGECARD 86POS DIP .100 SLD |
| MIC2592B-2YTQ | IC CTRLR HOTPLUG PCI DUAL 48TQFP |
| GRM1885C1H300JA01D | CAP CER 30PF 50V 5% NP0 0603 |
| T86C106M020EBSS | CAP TANT 10UF 20V 20% 2312 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1875 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:PON Triplexer and SFP Controller |
| DS1875RT+ | 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER AND SFP CONTROLLER - Rail/Tube |
| DS1875RT+T&R | 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER AND SFP CONTROLLER - Tape and Reel |
| DS1875T+ | 功能描述:ADC / DAC多通道 PON Triplexer & SFP Controller RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1875T+T&R | 制造商:Maxim Integrated Products 功能描述:PON TRIPLEXER 38TQFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SFP CTRLR/TRIPLEXER 38-TQFN 制造商:Maxim Integrated Products 功能描述:ADC / DAC Multichannel PON Triplexer & SFP Controller |
发布紧急采购，3分钟左右您将得到回复。