- 您现在的位置：买卖IC网 > PDF目录11706 > DS1884T+ (Maxim Integrated Products)IC SFP PON ONU CTRLR 24TQFN PDF资料下载
参数资料
| 型号： | DS1884T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 31/92页 |
| 文件大小： | 0K |
| 描述： | IC SFP PON ONU CTRLR 24TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 产品变化通告： | DS1884 Series Discontinuation 03/Aug/2012 |
| 标准包装： | 28 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
DS1884
SFP and PON ONU Controller
with Digital LDD Interface
37
Maxim Integrated
because it is busy. It is possible to take advantage
of that phenomenon by repeatedly addressing the
device, which allows the next page to be written as
soon as the device is ready to receive the data. The
alternative to acknowledge polling is to wait for maxi-
mum period of tW to elapse before attempting to write
again to the device.
EEPROM Write Cycles: When EEPROM writes occur,
the device writes the whole EEPROM memory page,
even if only a single byte on the page was modified.
Writes that do not modify all 8 bytes on the page are
allowed and do not corrupt the remaining bytes of
memory on the same page. Because the whole page
is written, bytes on the page that were not modified
during the transaction are still subject to a write cycle.
This can result in a whole page being worn out over
time by writing a single byte repeatedly. Writing a page
1 byte at a time wears the EEPROM out 8x faster than
writing the entire page at once. The device’s EEPROM
write cycles are specified in the Nonvolatile Memory
Characteristics table. The specification shown is at the
worst-case temperature. It can handle approximately
10x that many writes at room temperature. Writing to
SRAM-shadowed EEPROM memory with SEEB = 1
does not count as a EEPROM write cycle when evaluat-
ing the EEPROM’s estimated lifetime.
Reading a Single Byte from a Slave: Unlike the write
operation that uses the memory address byte to define
where the data is to be written, the read operation
occurs at the present value of the memory address
counter. To read a single byte from the slave, the
master generates a START condition, writes the slave
address byte with R/W = 1, reads the data byte with a
NACK to indicate the end of the transfer, and gener-
ates a STOP condition.
Manipulating the Address Counter for Reads: A
dummy write cycle can be used to force the address
pointer to a particular value. To do this, the master
generates a START condition, writes the slave address
byte (R/W = 0), writes the memory address where it
desires to read, generates a repeated START condi-
tion, writes the slave address byte (R/W = 1), reads
data with ACK or NACK as applicable, and generates
a STOP condition.
Memory Organization
The following sections provide the device’s register
definitions (see Figure 20 for the memory map). Each
register or row of registers has an access descriptor that
determines the password level required to read or write
the memory. Level 2 password is intended for the mod-
ule manufacture access only; level 1 password allows
another level of protection for items the end consumer
may wish to protect. Many registers are always readable,
but require password access to write. There are a few
registers that cannot be read without password access.
The below access codes describe each mode used by
the DS1884 with factory setting for the PW_ENA (A2h
Table 02h, Register C0h ) and PW_ENB (A2h Table 02h,
Register C1h) values set to factory settings.
ACCESS
CODE
READ ACCESS
WRITE ACCESS
<0>
At least 1 byte/bit in the row/byte is different
than the rest of the row/byte, so look at each
byte/bit separately for permissions.
<1>
Read all
Write PW2
<2>
Read all
Write not applicable
<3>
Read all
Write all, but the
device hardware
also writes to these
bytes/bits
<4>
Read PW2
Write PW2 +
mode_bit
<5>
Read all
Write all
<6>
Read not applicable
Write all
<7>
Read PW1
Write PW1
<8>
Read PW2
Write PW2
<9>
Read not applicable
Write PW2
<10>
Read PW2
Write not applicable
<11>
Read all
Write PW1
相关PDF资料 |
PDF描述 |
|---|---|
| MS27467E25A35SA | CONN PLUG 128POS STRAIGHT W/SCKT |
| GRM216R71H223KA01J | CAP CER 0.022UF 50V 10% X7R 0805 |
| VE-BVM-IX-F3 | CONVERTER MOD DC/DC 10V 75W |
| VE-BVM-IX-F2 | CONVERTER MOD DC/DC 10V 75W |
| GRM216F51H223ZA01D | CAP CER 0.022UF 50V Y5V 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS1884T+ | 功能描述:ADC / DAC多通道 SFP+ Controller w/ Digi LDD Interface RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1884T+T | 功能描述:ADC / DAC多通道 SFP+ Controller w/ Digi LDD Interface RoHS:否 制造商:Texas Instruments 转换速率: 分辨率:8 bit 接口类型:SPI 电压参考: 电源电压-最大:3.6 V 电源电压-最小:2 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-40 |
| DS1886 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:带有数字LDD接口的SFP和PON ONU控制器 |
| DS1886_V1 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SFP and PON ONU Controller with Digital LDD Interface |
| DS1886T+ | 功能描述:接口 - 专用 PON ONU/SFP CTRLR W/DIG LDD INT RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。