参数资料
型号: DS21348GN
厂商: Maxim Integrated Products
文件页数: 8/76页
文件大小: 0K
描述: IC LIU LN T1/E1/J1 3.3V 49-BGA
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 416
类型: 线路接口装置(LIU)
驱动器/接收器数: 1/1
规程: T1/E1/J1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 49-LFBGA,CSPBGA
供应商设备封装: 49-CSBGA(7x7)
包装: 托盘
DS21348/DS21Q348
16 of 76
NAME
PIN
I/O
FUNCTION
TTIP/
TRING
34/37
O
Transmit Tip and Ring [TTIP AND TRING]. Analog line driver
outputs. These pins connect via a step-up transformer to the line. See
Section 5 for details.
VDD
21/36
Positive Supply. 3.3V ±5%
VSM
20
I
Voltage Supply Mode. Should be low for 3.3V operation.
VSS
22/35
Signal Ground
WR (R/W)
3
I
Write Input (Read/Write), Active Low. See the bus timing
diagrams in Section 11.
Table 2-6. Pin Descriptions in Serial Port Mode (Sorted By Pin Name,
DS21348T Pin Numbering)
NAME
PIN
I/O
FUNCTION
BIS0/BIS1
32/33
I
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. See Table 2-1 for details.
BPCLK
31
O
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
CS
1
I
Chip Select, Active Low. Active-low signal must be low to read or
write to the device.
HRST
29
I
Hardware Reset, Active Low. Bringing
HRST low will reset the
DS21348 setting all control bits to their default state of all zeros.
ICES
8
I
Input Clock Edge Select. Selects whether the serial port data input
(SDI) is sampled on rising (ICES =0) or falling edge (ICES = 1) of
SCLK.
INT
23
O
Interrupt, Active Low. Flags host controller during conditions and
change of conditions defined in the Status Register. Active-low,
open-drain output.
MCLK
30
I
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional.
NA
I
Not Assigned. Should be tied low.
OCES
9
I
Output Clock Edge Select. Selects whether the serial port data
output (SDO) is valid on the rising (OCES = 1) or falling edge
(OCES = 0) of SCLK.
PBEO
24
O
PRBS Bit Error Output. The receiver will constantly search for a
215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
相关PDF资料
PDF描述
VI-241-MX-F3 CONVERTER MOD DC/DC 12V 75W
MAX214EPI+ IC TXRX RS-232 PROG 28-DIP
MAX214EWI+ IC TXRX RS-232 PROG 28-SOIC
HI5767/2IA CONV A/D 10BIT 20MSPS 28-SOIC
VI-242-MX-F4 CONVERTER MOD DC/DC 15V 75W
相关代理商/技术参数
参数描述
DS21348GN+ 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21348GNB 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21348GN-C01 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21348T 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21348T+ 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray