参数资料
型号: DS21348TN+
厂商: Maxim Integrated Products
文件页数: 6/76页
文件大小: 0K
描述: IC LIU T1/E1/J1 3.3V 44-TQFP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 160
类型: 线路接口装置(LIU)
驱动器/接收器数: 1/1
规程: T1/E1/J1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 44-TQFP
供应商设备封装: 44-TQFP(10x10)
包装: 托盘
产品目录页面: 1429 (CN2011-ZH PDF)
DS21348/DS21Q348
14 of 76
2.1 Pin Descriptions
Table 2-5. Pin Descriptions in Parallel Port Mode (Sorted by Pin Name,
DS21348T Pin Numbering)
NAME
PIN
I/O
FUNCTION
A0 to A4
11 to 7
I
Address Bus. In nonmultiplexed bus operation (BIS1 = 0, BIS0 =
1), serves as the address bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), these pins are not used and should be tied low.
ALE (AS)
4
I
Address Latch Enable (Address Strobe). When using the parallel
port (BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to
demultiplex the bus on a positive-going edge. In nonmultiplexed bus
mode (BIS0 = 1), should be tied low.
BIS0/BIS1
32/33
I
Bus Interface Select Bits 0 and 1. Used to select bus interface
option. See Table 2-1 for details.
BPCLK
31
O
Backplane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
CS
1
I
Chip Select, Active Low. This active-low signal must be low to
read or write to the device.
D0/AD0 to
D7/AD7
19 to 12
I/O
Data Bus/Address/Data Bus. In nonmultiplexed bus operation
(BIS1 = 0, BIS0 = 1), serves as the data bus. In multiplexed bus
operation (BIS1 = 0, BIS0 = 0), serves as an 8-bit multiplexed
address/data bus.
HRST
29
I
Hardware Reset, Active Low. Bringing
HRST low resets the
DS21348, setting all control bits to their default state of all zeros.
INT
23
O
Interrupt, Active Low. Flags host controller during conditions and
change of conditions defined in the Status Register. Active low,
open drain output.
MCLK
30
I
Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544MHz
clock source is optional.
N/A
I
Not Assigned. Should be tied low.
PBEO
24
O
PRBS Bit Error Output. The receiver will constantly search for a
215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
相关PDF资料
PDF描述
VE-B5J-MX-F2 CONVERTER MOD DC/DC 36V 75W
VE-B5J-MX-F1 CONVERTER MOD DC/DC 36V 75W
VE-B5J-MW CONVERTER MOD DC/DC 36V 100W
VE-B54-MX-F3 CONVERTER MOD DC/DC 48V 75W
T 3402 000 CONN CIR RCPT MALE 6POS PNL MNT
相关代理商/技术参数
参数描述
DS21348TN+ 功能描述:网络控制器与处理器 IC 3.3V E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21348TNB 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21348T-W 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray
DS21349 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:3.3V T1/J1 Line Interface Unit
DS21349DK 功能描述:网络开发工具 DS21349 Design Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V