- 您现在的位置：买卖IC网 > PDF目录97866 > DS2152L (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PQFP100 PDF资料下载
参数资料
| 型号： | DS2152L |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PQFP100 |
| 封装： | LQFP-100 |
| 文件页数： | 3/14页 |
| 文件大小： | 1398K |
| 代理商： | DS2152L |
11
Maxim Integrated
Adjustable Overvoltage and Overcurrent
Protectors with High Accuracy
MAX14571/MAX14572/MAX14573
Thermal-Shutdown Protection
The devices have a thermal-shutdown feature to pro-
tect them from overheating. The devices turn off and the
FLAG asserts when the junction temperature exceeds
+150NC (typ). The devices exit thermal shutdown and
resume normal operation after the junction temperature
cools by 30NC (typ), except for the MAX14572, which re-
mains latched off.
The thermal limit behaves similarly to the current limit. For
the MAX14571 (autoretry), the thermal limit works with the
autoretry timer. When the device comes out of the ther-
mal limit, it starts after the retry time. For the MAX14572
(latch off), the device latches off until power or EN cycle.
For the MAX14573 (continuous), the device only disables
while the temperature is over the limit. There is no blank-
ing time for thermal protection.
Overvoltage Lockout (OVLO)
The devices have a 33V (typ) preset OVLO threshold
when the voltage at OVLO is set below the external
OVLO select voltage (VOVLOSEL). Connect OVLO to
GND to activate the preset OVLO threshold. Connect
the external resistors to the OVLO pin as shown in the
Typical Operating Circuit to externally adjust the OVLO
threshold. Use the following equation to adjust the OVLO
threshold. The recommended value for R3 is 2.2MI:
OVLO
BG
R3
V
V1
R4
=
×+
Undervoltage Lockout (UVLO)
The devices have a 19.2V (typ) preset UVLO threshold
when the voltage at UVLO is set below the external
UVLO select voltage (VUVLOSEL). Connect UVLO to
GND to activate the preset UVLO threshold. Connect
the external resistors to the UVLO pin as shown in the
Typical Operating Circuit to externally adjust the UVLO
threshold. Use the following equation to adjust the UVLO
threshold. The recommended value for R1 is 2.2MI:
UVLO
BG
R1
V
V1
R2
=
×+
Switch Control
There are two independent enable inputs (HVEN and
EN) for the devices. HVEN is a high-voltage-capable
input. Toggle HVEN or EN to reset the fault condition
once a short circuit is detected and the devices shut
down (Table 1).
Input Debounce Protection
The ICs feature input debounce protection. When the
input voltage is higher than the UVLO threshold voltage
for a period greater than the debounce time (tDEB), the
internal FETs are turned on. This feature is intended for
applications where the EN or HVEN signal is present
when the power supply ramps up (Figure 4).
Applications Information
Setting the Current Limit/Threshold
A resistor from SETI to ground programs the current limit/
threshold value for the devices. Leaving SETI uncon-
nected selects a 0A current limit/threshold. Connecting
SETI to ground asserts FLAG. Use the following formula
to calculate the current limit:
=
SETI
LIM
11500
R
(k )
I
(mA)
IN Bypass Capacitor
Connect a minimum of 1FF capacitor from IN to GND
to limit the input voltage drop during momentary output
short-circuit conditions. Larger capacitor values further
reduce the voltage undershoot at the input.
Hot-Plug IN
In many system powering applications, an input-filtering
capacitor is required to lower the radiated emission,
enhance the ESD capability, etc. In hot-plug applica-
tions, parasitic cable inductance, along with the input
capacitor, cause overshoot and ringing when the pow-
ered cable is connected to the input terminal.
This effect causes the protection device to see almost
twice the applied voltage. An input voltage of 24V can
easily exceed the absolute maximum rating of 40V, which
may permanently damage the device. A transient voltage
suppressor (TVS) is often used for industrial applications
to protect the system from these conditions. We recom-
mend using a TVS that is capable of limiting surge to 40V
placed close to the input terminal.
Table 1. Switch Control
HVEN
EN
SWITCH STATUS
0
On
1
0
Off
0
1
On
1
On
相关PDF资料 |
PDF描述 |
|---|---|
| DS2153Q | DATACOM, FRAMER, PQCC44 |
| DS2154L | DATACOM, FRAMER, PQFP100 |
| DS21554L | DATACOM, PCM TRANSCEIVER, PQFP100 |
| DS21554LN | DATACOM, PCM TRANSCEIVER, PQFP100 |
| DS2155G | DATACOM, FRAMER, PBGA100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2152L+ | 功能描述:网络控制器与处理器 IC Enhanced T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2152L-ES | 制造商:DALL 功能描述: |
| DS2152LN | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2152LN+ | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2153DK | 功能描述:KIT DESIGN TXRX E1 DS2153 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。