- 您现在的位置：买卖IC网 > PDF目录11005 > DS21554L+ (Maxim Integrated Products)IC TXRX E1 1-CHIP 5V 100-LQFP PDF资料下载
参数资料
| 型号： | DS21554L+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 106/124页 |
| 文件大小： | 0K |
| 描述： | IC TXRX E1 1-CHIP 5V 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 功能： | 单芯片收发器 |
| 接口： | E1，HDLC，J1，T1 |
| 电路数： | 1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 电流 - 电源： | 75mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 托盘 |
| 包括： | 远程和 AIS 警报检测器 / 发生器 |
| 产品目录页面： | 1430 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页当前第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页
DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers
82 of 124
Table 15-2. Line Build-Out Select in LICR for the DS21354
L2
L1
L0
APPLICATION
TRANSFORMER
RETURN LOSS (dB)*
RT (
W)
**
0
75
W normal
1:2 step-up
N.M.
0
1
120
W normal
1:2 step-up
N.M.
0
1
0
75
W with protection resistors
1:2 step-up
N.M.
2.5
0
1
120
W with protection resistors
1:2 step-up
N.M.
2.5
1
0
75
W with high return loss
1:2 step-up
21
6.2
1
0
1
120
W with high return loss
1:2 step-up
21
11.6
* N.M. = Not Meaningful (return loss value too low for significance).
** Refer to Application Note 324 for details on E1 line interface design.
Due to the nature of the design of the transmitter in the DS21354/DS21554, very little jitter (less than
0.005 UIP-P broadband from 10Hz to 100kHz) is added to the jitter present on TCLK. Also, the waveform
created is independent of the duty cycle of TCLK. The transmitter in the device couples to the E1-
transmit-shielded twisted pair or coax via a 1:1.15 or 1:1.36 step-up transformer as shown in Figure 15-1.
For the devices to create the proper waveforms, the transformer used must meet the specifications listed
in Table 15-3. The line driver in the device contains a current limiter that prevents more than 50mA
(RMS) from being sourced in a 1
W load.
Table 15-3. Transformer Specifications
SPECIFICATION
RECOMMENDED VALUE
Turns Ratio for DS21354
1:1 (receive) and 1:2 (transmit) ±3%
Turns Ratio for DS21554
1:1 (receive) and 1:1.15 or 1:1.36 (transmit) ±3%
Primary Inductance
600
mH minimum
Leakage Inductance
1.0
mH maximum
Intertwining Capacitance
40pF maximum
DC Resistance
1.2
W maximum
15.3.
Jitter Attenuator
The DS21354/DS21554 contain an on-board jitter attenuator that can be set to a depth of either 32 or 128
bits via the JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in
applications where large excursions of wander are expected. The 32-bit mode is used in delay-sensitive
applications. The characteristics of the attenuation are shown in Figure 15-4. The jitter attenuator can be
placed in either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the
LICR. Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA bit in the LICR.
For the jitter attenuator to properly operate, a 2.048MHz clock (±50ppm) must be applied at the MCLK
pin, or a crystal with similar characteristics must be applied across the MCLK and XTALD pins. If a
crystal is applied across the MCLK and XTALD pins, then the maximum effective series resistance
should be 30
W, and capacitors should be placed from each leg of the crystal to ground as shown in
Figure 15-2. On-board circuitry adjusts either the recovered clock from the clock/data recovery block or
the clock applied at the TCLKI pin to create a smooth jitter-free clock, which is used to clock data out of
the jitter attenuator FIFO. It is acceptable to provide a gapped/bursty clock at the TCLKI pin if the jitter
attenuator is placed on the transmit side. If the incoming jitter exceeds either 120 UIP-P (buffer depth is
128 bits) or 28 UIP-P (buffer depth is 32 bits), then the DS21354/DS21554 divide the internal nominal
32.768MHz clock by either 15 or 17 instead of the normal 16 to keep the buffer from overflowing. When
the device divides by either 15 or 17, it also sets the Jitter Attenuator Limit Trip (JALT) bit in the Receive
Information Register (RIR.5).
相关PDF资料 |
PDF描述 |
|---|---|
| S9S08SG32E1MTG | MCU 32K FLASH 16-TSSOP |
| MC9S08JM8CLC | MCU 8BIT 8K FLASH 32-LQFP |
| DS21352L+ | IC TXRX T1 1-CHIP 3.3V 100-LQFP |
| MC9S08AC16CBE | IC MCU 8BIT 16K FLASH 42SDIP |
| DS21352LB+ | IC TXRX T1 1-CHIP 3.3V 100-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21554L+ | 功能描述:网络控制器与处理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21554LB | 功能描述:网络控制器与处理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21554LB+ | 功能描述:网络控制器与处理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21554LBN | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21554LBN+ | 功能描述:网络控制器与处理器 IC 3.3/5V E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。