参数资料
| 型号： | DS21FT44N+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 88/117页 |
| 文件大小： | 0K |
| 描述： | IC FRAMER 4X4 16CH 300-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 控制器类型： | E1 调帧器 |
| 接口： | 并行/串行 |
| 电源电压： | 2.97 V ~ 3.63 V |
| 电流 - 电源： | 225mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 300-BBGA |
| 供应商设备封装： | 300-PBGA（27x27） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页当前第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页
DS21FT44/DS21FF44
72 of 117
register. The read result should be logically AND’ed with the mask byte that was just written and this
value should be written back into the same register to insure that bit does indeed clear. This second write
step is necessary because the alarms and events in the status registers occur asynchronously in respect to
their access by the parallel port. This write-read-write (for polled-driven access) or write–read (for
interrupt driven access) scheme allows an external microcontroller or microprocessor to individually poll
certain bits without disturbing the other bits in the register. This operation is key in controlling the
DS21Q44 with higher order software languages.
Like the SR1 and SR2 status registers, the HSR register has the unique ability to initiate a hardware
interrupt by the INT* output pin. Each of the events in the HSR can be either masked or unmasked from
the interrupt pin by the HDLC Interrupt Mask Register (HIMR). Interrupts will force the INT* pin low
when the event occurs. The INT* pin will be allowed to return high (if no other interrupts are present)
when the user reads the event bit that caused the interrupt to occur.
19.3. BASIC OPERATION DETAILS
As a basic guideline for interpreting and sending HDLC messages, the following sequences can be
applied:
Receive a HDLC Message
1) Enable RPS interrupts.
2) Wait for interrupt to occur.
3) Disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt.
4) Read RHIR to obtain REMPTY status.
a) If REMPTY = 0, then record OBYTE, CBYTE, and POK bits and then read the FIFO
a1) If CBYTE = 0 then skip to Step 5
a2) If CBYTE = 1 then skip to Step 7
b) If REMPTY = 1, then skip to Step 6
5) Repeat Step 4.
6) Wait for interrupt, skip to Step 4.
7) If POK = 0, then discard whole packet, if POK = 1, accept the packet.
8) Disable RPE, RNE, or RHALF interrupt, enable RPS interrupt and return to Step 1.
Transmit a HDLC Message
1) Make sure HDLC controller is done sending any previous messages and is current sending flags by
checking that the FIFO is empty by reading the TEMPTY status bit in the THIR register.
2) Enable either the THALF or TNF interrupt.
3) Read THIR to obtain TFULL status.
a) If TFULL = 0, then write a byte into the FIFO and skip to next step (special case occurs
when the last byte is to be written, in this case set TEOM = 1 before writing the byte and
then skip to Step 6)
b) If TFULL = 1, then skip to Step 5
4) Repeat Step 3.
5) Wait for interrupt, skip to Step 3.
6) Disable THALF or TNF interrupt and enable TMEND interrupt.
7) Wait for an interrupt, then read TUDR status bit to make sure packet was transmitted correctly.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21Q352B | IC TXRX QUAD T1/E1 3.3V 256-BGA |
| DS21Q41BT | IC FRAMER T1 QUAD 128-TQFP |
| DS21Q42T+ | IC FRAMER ENHANCED T1 4X 128TQFP |
| DS21Q43-ATN | IC FRAMER E1 QUAD 5V 128-TQFP |
| DS21Q44T+ | IC FRAMER ENHANCED E1 4X 128TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21FT44N+ | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q348 | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q348B | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q348DK | 功能描述:网络开发工具 RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| DS21Q348N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。