参数资料
| 型号： | DS21FT44N+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 98/117页 |
| 文件大小： | 0K |
| 描述： | IC FRAMER 4X4 16CH 300-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 控制器类型： | E1 调帧器 |
| 接口： | 并行/串行 |
| 电源电压： | 2.97 V ~ 3.63 V |
| 电流 - 电源： | 225mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 300-BBGA |
| 供应商设备封装： | 300-PBGA（27x27） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页当前第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页
DS21FT44/DS21FF44
81 of 117
TDC2: TRANSMIT HDLC DS0 CONTROL REGISTER 2 (Address = BB Hex)
(MSB)
(LSB)
TDB8
TDB7
TDB6
TDB5
TDB4
TDB3
TDB2
TDB1
SYMBOL
POSITION
NAME AND DESCRIPTION
TDB8
TDC2.7
DS0 Bit 8 Suppress Enable. MSB of the DS0. Set to one to
stop this bit from being used.
TDB7
TDC2.6
DS0 Bit 7 Suppress Enable. Set to one to stop this bit from
being used.
TDB6
TDC2.5
DS0 Bit 6 Suppress Enable. Set to one to stop this bit from
being used.
TDB5
TDC2.4
DS0 Bit 5 Suppress Enable. Set to one to stop this bit from
being used.
TDB4
TDC2.3
DS0 Bit 4 Suppress Enable. Set to one to stop this bit from
being used.
TDB3
TDC2.2
DS0 Bit 3 Suppress Enable. Set to one to stop this bit from
being used.
TDB2
TDC2.1
DS0 Bit 2 Suppress Enable. Set to one to stop this bit from
being used.
TDB1
TDC2.0
DS0 Bit 1 Suppress Enable. LSB of the DS0. Set to one to
stop this bit from being used.
20.
INTERLEAVED PCM BUS OPERATION
In many architectures, the outputs of individual framers are combined into higher speed serial buses to
simplify transport across the system. The DS21Q44 can be configured to allow each framer’s data and
signaling busses to be multiplexed into higher speed data and signaling busses eliminating external
hardware saving board space and cost.
The interleaved PCM bus option supports two bus speeds and interleave modes. The 4.096MHz bus
speed allows two framers to share a common bus. The 8.192MHz bus speed allows all four of the
DS21Q44’s framers to share a common bus. Framers can interleave their data either on byte or frame
boundaries. Framers that share a common bus must be configured through software and require several
device pins to be connected together externally (Figures 20-1 and 20-2). Each framer’s elastic stores must
be enabled and configured for 2.048MHz operation. The signal RSYNC must be configured as an input
on each framer.
For all bus configurations, one framer will be configured as the master device and the remaining framers
on the shared bus will be configured as slave devices. Refer to the IBO register description below for
more detail. In the 4.096MHz bus configuration there is one master and one slave per bus. Figure 20-1
shows the DS21Q44 configured to support two 4.096 MHz buses. Bus 1 consists of framers 0 and 1. Bus
2 consists of framers 2 and 3. Framers 0 and 2 are programmed as master devices. Framers 1 and 3 are
programmed as slave devices. In the 8.192 MHz bus configuration there is one master and three slaves.
Figure 20-2 shows the DS21Q44 configured to support an 8.192MHz bus. Framer 0 is programmed as the
master device. Framers 1, 2, and 3 are programmed as slave devices. Consult timing diagrams in section
22 for additional information.
When using the frame interleave mode, all framers that share an interleaved bus must have receive signals
(RPOS and RNEG) that are synchronous with each other. The received signals must originate from the
same clock reference. This restriction does not apply in the byte interleave mode.
相关PDF资料 |
PDF描述 |
|---|---|
| DS21Q352B | IC TXRX QUAD T1/E1 3.3V 256-BGA |
| DS21Q41BT | IC FRAMER T1 QUAD 128-TQFP |
| DS21Q42T+ | IC FRAMER ENHANCED T1 4X 128TQFP |
| DS21Q43-ATN | IC FRAMER E1 QUAD 5V 128-TQFP |
| DS21Q44T+ | IC FRAMER ENHANCED E1 4X 128TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21FT44N+ | 功能描述:网络控制器与处理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q348 | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q348B | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q348DK | 功能描述:网络开发工具 RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| DS21Q348N | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。