- 您现在的位置：买卖IC网 > PDF目录378591 > DS2282 T1 FDL Controller/Monitor Stik PDF资料下载
参数资料
| 型号： | DS2282 |
| 英文描述： | T1 FDL Controller/Monitor Stik |
| 中文描述： | T1 FDL控制器/监视器条 |
| 文件页数： | 14/22页 |
| 文件大小： | 192K |
| 代理商： | DS2282 |
DS2282
022798 14/22
necessary data to create a PRM from both the monitor
registers and from the SLIP signal. It creates the open-
ing and closing flags as well as the address and control
bytes. Once the PRM packet has been assembled, the
DS2282 will generate CRC–16 and include it at the end
of the PRM. And finally, before the PRM is sent, zeros
are inserted to insure that none of the PRM data ap-
pears as a flag.
Receive Unscheduled Message Operation
The DS2282 decodes incoming unscheduled mes-
sages as they are received. The DS2282 will report the
received unscheduled message via the RUMR when
the message has been received for three consecutive
times. This integration allows the DS2282 to operate
properly even on high bit error rate lines. The RUMR is
cleared when read via the serial port. The INT pin will be
asserted (transitions low), indicating to an external con-
troller that an unscheduled message has been received
three consecutive times. The user may count incoming
unscheduled messages by monitoring the INT pin. The
INT pin will return high as soon as the RUMR is ac-
cessed.
Two output signals on the DS2282 will respond to cer-
tain unscheduled messages. The PLB (Payload Loop-
back) signal will transition high if the code word for pay-
load loopback activate (001010) is received three times.
It will remain high until the DS2282 has received the
payload loopback deactivate code word (011001) three
times. The LLB (Line Loopback) signal operates simi-
larly. The LLB signal will transition high when the
DS2282 has received the code word for line loopback
activate (000111) three times. It will remain high until the
DS2282 has received the code word for line loopback
deactivate (011100) three times. The user has the op-
tion to control the PLB and LLB pins via the Loopback
Control Register (LBCR); see “Loopback Control Regis-
ter.”
RUMR: Receive Unscheduled Message
Register (18)
NA
NA
CW5
CW4
CW3
CW2
CW1
CW0
(LSB)
(MSB)
NA
Not Assigned. Could be any value when
read.
NA
Not Assigned. Could be any value when
read.
MSB of the Receive Unscheduled Mes-
sage Code word.
LSB of the Receive Unscheduled Mes-
sage Code word.
CW5
CW0
Transmit Unscheduled Message Operation
The DS2282 will transmit outgoing unscheduled mes-
sages. The DS2282 will continuously transmit the un-
scheduled message described in TUMR if enabled via
the TUM bit in the TUMR. If unscheduled messages are
being transmitted, all PRMs are superseded. When the
TUM is cleared, the DS2282 will finish sending the un-
scheduled message that it is currently transmitting be-
fore switching to either the idle code or PRMs.
TUMR: Transmit Unscheduled Message
Register (19)
TUM
0
CW5
CW4
CW3
CW2
CW1
CW0
(LSB)
(MSB)
TUM
CW5
Transmit Unscheduled Message Enable
MSB of the Transmit Unscheduled Mes-
sage Code word.
LSB of the Transmit Unscheduled Mes-
sage Code word.
PAR: PRM Address Register (1F)
. The DS2282
allows the user to set the PRM opening address C/R bit
depending on the source of the PRM. The C/R bit is set
to zero for PRMs created by user equipment such as a
CPE or set to one for PRMs created by a carrier. The
PAR allows the user to control the expected state of the
C/R bit as well as control the state of the bit in the PRMs
created by the DS2282.
CW0
0
0
0
0
0
0
TC/R
RC/R
(LSB)
(MSB)
TC/R
Transmit PRM C/R Bit Control
0=force C/R bit to zero in outgoing PRM
1=force C/R bit to one in outgoing PRM
Receive PRM C/R Bit Control
0=only respond to RPM with the C/R bit set
to zero
1=only respond to PRM with the C/R bit set
to one
RC/R
相关PDF资料 |
PDF描述 |
|---|---|
| DS2411X | Silicon Serial Number with VCC Input |
| DS2411 | Silicon Serial Number with VCC Input |
| DS2411P | Silicon Serial Number with VCC Input |
| DS2431 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| DS2431P | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2282/87-22282-000 | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2282-113 | 功能描述:IC CTRLR/MON STIK T1 FDL 30-PIN RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| DS2286-8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS2287-32 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS2287-8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。