- 您现在的位置：买卖IC网 > PDF目录378591 > DS2282 T1 FDL Controller/Monitor Stik PDF资料下载
参数资料
| 型号： | DS2282 |
| 英文描述： | T1 FDL Controller/Monitor Stik |
| 中文描述： | T1 FDL控制器/监视器条 |
| 文件页数： | 6/22页 |
| 文件大小： | 192K |
| 代理商： | DS2282 |
DS2282
022798 6/22
PIN
DESCRIPTION
TYPE
SYMBOL
22
NC
–
No Connect
. Do not connect any signal to this pin.
23
GND
–
Ground
. 0.0 volts.
24
25
UB5
UB6
O
User Bits 5 to 6
. Each user bit can be independently configured either
high or low via the UBR register. In hardware mode, tied high or low exter-
nally to configure DS2282.
26
LLB
O
Line Loopback
. Transitions high when the code word for line loopback
activate has been received; transitions low when the code word for line
loopback deactivate has been received. This pin does not go active in a
54016 environment.
27
PSEN
–
Program Store Enable
. Used in conjunction with the RST pin to program
the onboard nonvolatile memory. In normal applications, do not connect
any signal to this pin.
28
TLINK
O
Transmit Link Data
. FDL data to be transmitted; updated on the falling
edge of TLCLK.
29
NC
–
No Connect
. Do not connect any signal to this pin.
30
NC
–
No Connect
. Do not connect any signal to this pin.
SERIAL PORT OPERATION
The registers in the DS2282 are controlled via a two–
wire, asynchronous serial port. All but four of the regis-
ters are read–only; UBR, PAR, LBCR, and TUMR are
write only. See Tables 2 through 5. Registers on the
DS2282 are read from or written to one at a time. Com-
munication over the serial port to one of the registers
normally consists of either three, four, or five bytes.
(Note: reads from the ESICR, UASICR, BESICR, SE-
SICR, or CSLFICR consists of 194 bytes: two written to
the DS2282 and 192 read from the Stik.) The first byte is
always written to the DS2282 and is called the Address
Byte. Normally, all communications via the asynchro-
nous serial port on the DS2282 are performed in 11–bit
bursts. See Figure 4. There is a Start Bit which is al-
ways a zero, followed by eight data bits (LSB first), fol-
lowed by an Extra Bit which is a one in the Address Byte
and a zero in the Register and Data Bytes, followed fi-
nally by a Stop Bit which is always a one. If the user
wishes to eliminate the need for the Extra Bit in the serial
port communications of the DS2282, then either the se-
rial port address on the Stik must be set to decimal 31
(how to set the serial port address on the DS2282 is de-
scribed in “Initializing the Address of the Serial Port”) or
the DRVEN pin (pin 9) must be tied permanently low. If
the user ties DRVEN low, then the address defaults to
zero.
DS2282 SERIAL PORT COMMUNICATIONS
Figure 4
D0
D1
D2
D3
D4
D5
D6
D7
EBIT
BIT
SBIT
(LSB)
(MSB)
D0
D1
D2
D3
D4
D5
D6
D7
BIT
SBIT
(LSB)
(MSB)
RXD
1
TXD
RXD
2
TXD
NOTES:
1. If the serial port is programmed for addresses between 0 and 30 decimal (inclusive)
2. If the serial port is programmed for address 31 decimal or if DRVEN tied low
相关PDF资料 |
PDF描述 |
|---|---|
| DS2411X | Silicon Serial Number with VCC Input |
| DS2411 | Silicon Serial Number with VCC Input |
| DS2411P | Silicon Serial Number with VCC Input |
| DS2431 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| DS2431P | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2282/87-22282-000 | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2282-113 | 功能描述:IC CTRLR/MON STIK T1 FDL 30-PIN RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:4,900 系列:- 控制器类型:USB 2.0 控制器 接口:串行 电源电压:3 V ~ 3.6 V 电流 - 电源:135mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:36-VFQFN 裸露焊盘 供应商设备封装:36-QFN（6x6） 包装:* 其它名称:Q6396337A |
| DS2286-8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS2287-32 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
| DS2287-8 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。