参数资料
| 型号： | DS2431Q+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/27页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 1KBIT 6TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K（256 x 4） |
| 接口： | 1 线 串行 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 6-WDFN 裸露焊盘 |
| 供应商设备封装： | 6-TDFN 裸露焊盘（3x3） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
DS2431
1024-Bit, 1-Wire EEPROM
Contact the factory to set up and register a custom
manufacturer ID. The last row is reserved for future
use. It is undefined in terms of R/W functionality and
should not be used.
In addition to the main EEPROM array, an 8-byte
volatile scratchpad is included. Writes to the EEPROM
array are a two-step process. First, data is written to the
scratchpad and then copied into the main array. This
allows the user to first verify the data written to the
scratchpad prior to copying into the main array. The
device only supports full row (8-byte) copy operations.
For data in the scratchpad to be valid for a copy opera-
tion, the address supplied with a Write Scratchpad
command must start on a row boundary, and 8 full
bytes must be written into the scratchpad.
The protection control registers determine how incom-
ing data on a Write Scratchpad command is loaded
into the scratchpad. A protection setting of 55h (write
protect) causes the incoming data to be ignored and
the target address main memory data to be loaded into
the scratchpad. A protection setting of AAh (EPROM
mode) causes the logical AND of incoming data and
target address main memory data to be loaded into the
scratchpad. Any other protection control register set-
ting leaves the associated memory page open for unre-
stricted write access. Note: For the EPROM mode to
function, the entire affected memory page must first be
programmed to FFh. Protection-control byte settings of
55h or AAh also write protect the protection-control
byte. The protection-control byte setting of 55h does
not block the copy. This allows write-protected data to
be refreshed (i.e., reprogrammed with the current data)
in the device.
The copy-protection byte is used for a higher level of
security and should only be used after all other protec-
tion control bytes, user bytes, and write-protected
pages are set to their final value. If the copy-protection
byte is set to 55h or AAh, all copy attempts to the regis-
ter row and user-byte row are blocked. In addition, all
copy attempts to write-protected main memory pages
(i.e., refresh) are blocked.
Address Registers and Transfer Status
The DS2431 employs three address registers: TA1,
TA2, and E/S (Figure 6). These registers are common to
many other 1-Wire devices but operate slightly differ-
ently with the DS2431. Registers TA1 and TA2 must be
loaded with the target address to which the data is writ-
ten or from which data is read. Register E/S is a read-
only transfer-status register used to verify data integrity
with write commands. E/S bits E[2:0] are loaded with
the incoming T[2:0] on a Write Scratchpad command
and increment on each subsequent data byte. This is,
in effect, a byte-ending offset counter within the 8-byte
scratchpad. Bit 5 of the E/S register, called PF, is a
logic 1 if the data in the scratchpad is not valid due to a
loss of power or if the master sends fewer bytes than
needed to reach the end of the scratchpad. For a valid
write to the scratchpad, T[2:0] must be 0 and the mas-
ter must have sent 8 data bytes. Bits 3, 4, and 6 have
no function; they always read 0. The highest valued bit
of the E/S register, called authorization accepted (AA),
acts as a flag to indicate that the data stored in the
scratchpad has already been copied to the target
memory address. Writing data to the scratchpad clears
this flag.
BIT #
TARGET ADDRESS (TA1)
TARGET ADDRESS (TA2)
7
T7
T15
6
T6
T14
5
T5
T13
4
T4
T12
3
T3
T11
2
T2
T10
1
T1
T9
0
T0
T8
ENDING ADDRESS WITH
DATA STATUS (E/S)
AA
0
PF
0
0
E2
E1
E0
(READ ONLY)
Figure 6. Address Registers
8
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| DS2431P+T&R | IC EEPROM 1KBIT 6TSOC |
| DS2431+T&R | IC EEPROM 1KBIT TO92-3 |
| FT24C128A-UMR-B | IC EEPROM 128KBIT 1MHZ 8MSOP |
| FT24C128A-UDR-B | IC EEPROM 128KBIT 1MHZ 8DIP |
| FT24C128A-UTG-B | IC EEPROM 128KBIT 1MHZ 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2431QU | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1024-Bit, 1-Wire EEPROM |
| DS2431X | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2431X+ | 功能描述:电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| DS2431X+S | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1024-Bit, 1-Wire EEPROM |
| DS2431X+U | 功能描述:电可擦除可编程只读存储器 1024-BIT 1-WIRE 电可擦除可编程只读存储器 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。