参数资料
型号: DS2450S+
厂商: Maxim Integrated Products
文件页数: 10/25页
文件大小: 0K
描述: IC CONVERTER A/D QUAD 1-W 8-SOIC
产品培训模块: 1-Wire Communications
Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
产品变化通告: Product Discontinuation 27/Jul/12
标准包装: 88
位数: 16
采样率(每秒): 1k
数据接口: 串行
转换器数目: 1
功率耗散(最大): 2.5mW
电压电源: 单电源
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.209",5.30mm 宽)
供应商设备封装: 8-SOIC
包装: 管件
输入数目和类型: 4 个单端,单极
产品目录页面: 1429 (CN2011-ZH PDF)
DS2450
18 of 24
USAGE EXAMPLE (control channel A and channel B outputs)
MASTER MODE
DATA (LSB FIRST) COMMENTS
TX
Reset
Reset Pulse (480 - 960 μs)
RX
Presence
Presence Pulse
TX
CCh
Issue “Skip ROM” Command
TX
55h
Issue “Write Memory” Command
TX
08h
TA1, beginning address
TX
00h
TA2, address = 0008h
TX
80h if AFL = 1 / C0h if
AFL = 0
data byte (address 0008)
CH-A
RX
<CRC16>
CRC of command, address, data byte
RX
<data byte>
read-back for simple verification
TX
00h
next data byte (address 0009h)*
RX
<CRC16>
CRC of address, data byte
RX
00h
read-back for simple verification
TX
80h if AFH = 1 / C0h if
AFH = 0
data byte (address 000A)
CH-B
RX
<CRC16>
CRC of address, data byte
RX
<data byte>
read-back for simple verification
TX
Reset
Reset Pulse (480 - 960 μs)
RX
Presence
Presence Pulse
*In a multi-drop environment it takes less time to perform a non-changing write cycle rather than
skipping a byte.
1-WIRE SIGNALING
The DS2450 requires strict protocols to ensure data integrity. The protocol consists of four types of
signaling on one line: reset sequence with reset pulse and presence pulse, Write 0, Write 1 and Read Data.
All these signals except presence pulse are initiated by the bus master. The DS2450 can communicate at
two different speeds, regular speed and Overdrive Speed. If not explicitly set into the Overdrive mode,
the DS2450 will communicate at regular speed. While in Overdrive mode the fast timing applies to all
wave forms.
The initialization sequence required to begin any communication with the DS2450 is shown in Figure 10.
A Reset Pulse followed by a Presence Pulse indicates the DS2450 is ready to send or receive data given
the correct ROM command and memory function command. The bus master transmits (TX) a reset pulse
(tRSTL, minimum 480 μs at regular speed, 48 μs at Overdrive Speed). The bus master then releases the
line and goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pullup resistor.
After detecting the rising edge on the data pin, the DS2450 waits (tPDH,15-60 μs at regular speed, 2-6 μs
at Overdrive speed) and then transmits the Presence Pulse (tPDL, 60-240 μs at regular speed, 8-24 μs at
Overdrive Speed).
A Reset Pulse of 480 μs or longer will exit the Overdrive Mode returning the device to regular speed. If
the DS2450 is in Overdrive Mode and the Reset Pulse is no longer than 80 μs the device will remain in
Overdrive Mode.
相关PDF资料
PDF描述
MC100LVEP16DTG IC RECEIVER/DRVR ECL DIFF 8TSSOP
DS3150Q IC LIU T3/E3/STS-1 28-PLCC
VE-26W-IU-F1 CONVERTER MOD DC/DC 5.5V 200W
NB7VPQ16MMNTXG IC COPPER/CABLE DVR PROG 16-QFN
MS27473E12F98PB CONN PLUG 10POS STRAIGHT W/PINS
相关代理商/技术参数
参数描述
DS2450S/T&R 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
DS2450S+ 功能描述:模数转换器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32
DS2450S+ 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW))
DS2450S+T&R 制造商:Maxim Integrated Products 功能描述:IC CONVERTER A/D QUAD 1-W 8-SOIC
DS2450S+T&R 功能描述:模数转换器 - ADC Quad 1-Wire RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32